Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Hilltopmike

1991 LT-F4WDX 280CC King Quad Need Right Front Axle

Recommended Posts

Hi Folks,

Just bought this 1991 King Quad and it is missing the right front axle.  It runs and drives in 2 wd, would be nice to find parts or whole axle to make the 4 wd drive work again.  A rebuildable  axle would be fine.  Any help would be great.  

Thanks Hilltopmike

kingquadsideplastic.jpg

Share this post


Link to post
Share on other sites


That’s going to be a tough part to find.  I would keep checking eBay and maybe a few other web pages.  But they will charge through the roof! Hopefully you can find a used on and get it rebuilt. 

Share this post


Link to post
Share on other sites
Guest

Got a brand new one on the shelf. 54901-19B81-000  They retail at $505.41 

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By MarkinAR
      And the new 300FW is already wounded. Something got in a bind and blew the whole chunk of case out around the primary drive gear at the back of the motor. In the pic you can see the crack along the top...there is a big chunk missing from the bottom. And it won't roll....but the front and rear diffs both seem fine. Unfortunate. This looks to be a bit of a project. Still feels like it will shift through gears so i'm wondering if the ring and pinion just jumped a bit and blew something to pieces.  I have a parts bike.  But will this require the case to be split and transmission completely disassembled?  I assume you can't just slide the broken primary drive out and slide the replacement in?
       

    • By Randel1
      I am trying to put a 1994 Suzuki 250 quadrunner back into service. I have it up and running like new but need to replace the plastics as they are brittle and crumbling due to age and sun exposure. I would like to purchase new parts either OEM or aftermarket but have had little luck in finding them. I would even consider used or salvaged parts in serviceable condition. Any help in locating these parts would be greatly appreciated. Thanks in advance.
    • By MarkinAR
      So just as a general FYI, it might be good to check replacement parts before installing.  If possible, check clearances with a micrometer before going through the trouble of assembly.  I say this as I bought a new driveshaft yoke for a Kodiak because the ujoint dropped a cap and got the yoke in a bind...blowing the yoke and middle drive gear to shreds.  So I replaced the middle drive gear and bought a new yoke and ujoint kit from Caltric.  Caltric is usually pretty solid replacement parts.  The new yoke however was a good 4mm too narrow for inside lock ujoint caps.  Disappointing since it came as a kit from Caltric.
      Ended up taking an angle grinder to the new yoke and thinning material off to get it to the needed 41.25mm opening size.  Sucks having to disassemble everything again and start over but my fault for trusting replacement parts.  Nearly 40 years of turning wrenches and I made a rookie mistake.
    • By Dwight Williams
      Ok, so I bought this scream of a deal the other day - a 94 King Quad 300 for $40.00.  It's been sitting outside with no carburetor on it for about a year.  Its rusty, missing some parts, wiring is all cut up and spliced etc.  No seat, no racks but the plastic is all there minus the headlight housing.  Anyway, who can pass up a $40.00 quad right?  I get it home and looked at the sight glass for oil level, it's about 1/2 oil and 1/2 water.  I drain it, refill it and turn the motor by hand (recoil starter is missing) and it turns over just fine.  I worked on the wiring for about an hour and got it to turn over with the electric starter and got enough of it sorted out to get a spark.  Did a quick compression test, 70 lbs.  Wet test bumped it up to 90.  Ok, so rings and cylinder washed out with water for a year, not too surprised.  I thought 'what the hell' and sprayed some starting fluid in it and it ran for about 2 seconds - enough to show  it's got life.  Since then the compression has gotten worse, I can't get enough pressure to activate the carb diaphragm, therefore no fuel pump either.  The compression is now around 60.
        Anyway, my question is....is it worth it to try to get this thing going?  I tore the top end down today and the cam and one of the rockers is pretty worn.  I figured a top end job would be about $100 or so, depending on the condition of the cylinder but I'll probably have to put a cam and rockers in it as well.  Doing some research on ebay I figure I'll have to spend about $500-$700 to make the whole machine right again.  Much less just to make it run and use as-is but I won't really like it until it's right.  I don't mind doing the work, I actually enjoy it but I'm concerned about what all that water did to the rest of the internals, I can't really test it all out until I can make it run.
      I know it's a basket case but I'm not into it much at all, even if I do the top end and find something else wrong I'm still not out much.  I'm leaning toward ordering the top end parts and going from there unless you can convince me otherwise - any way to check the rest of the internals without tearing it down?  I plan on flushing the oil cooler before I do another oil change, I've drained it twice now and it gets milky almost immediately just turning the starter - I suspect the oil cooler is polluted badly.
       
      I'll get some pictures today if anyone want to see them.
       
      thanks!
  • Similar Tagged Content

    • By Bubba Blaster
      Hi there, new owner to a Bayou 220 and could use some input from those who have owned these. At idle only, I am hearing a distinctly noticeable amount of chatter noise coming from the lower right side of the engine - right in the the clutch housing area. It's like a light clanking sound like something is loose in there. It goes away as soon as you give it throttle. Shifting in and out of gear is smooth and there is no change in the noise if you have it in or out of gear. The clutch doesn't slip at all, it's just that noise. I can also feel it when my hand is on the the clutch housing.
      I just replaced the oil and filter with 10w30 motor oil per spec. Any thoughts?
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...