Join Today, It's Simple and FREE!
As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery. Registration is fast and you can even login with social network accounts to sync your profiles and content.
My ranger crew 700 is hard to shift and gets locked into forward. When trying to shift into reverse we have to shut engine off. Shift then restart. Checked linkage and gears are fine. The RPMs arent really that high but did notice a little improvement when we lowered it. Did notice the throttle cable looks damaged. Could this be the issue?
Let me start with I have about 30 years of ATC experience, but not much with stuff made after 1988. Some, but I'm mechanically inclined so it's all good. I"m rehabbing a 1997 Bayou 220 to send back into the wild and the mechanicals are now all good, just working on making the electrical system...electric. Right now, I have no power on the white wire as tested directly on the plug at the starter solenoid. I'm assuming that wire is supposed to be hot any time it's attached to a battery? The genius that had it before snipped a couple wires and inserted a fairly heavy push button for electric start bypassing the electrical system. I think i've corrected everything north of the solenoid but the white wire has me stumped. Is my assumption that this should always be hot with a hot battery correct? Does this indicate a broken circuit in the starter solenoid? Relay was also bad and wired incorrectly, but that's resolved and I can make the relay click bypassing the solenoid and connector, directly giving the white wire 12V. Thoughts?
I am looking to see why my 2005 Grizzly 660 won't crank. I have set the valves but suspect a loose timing chain.
When working to remove the valve cover I found a "cap tensioner case" - parts #25 - #299 on Babbitts site.
The cover seems to bridge the valve cover and the cylinder head. What the hell is it and what surprises will I find if I remove it?
Uncharted territory for me.
By mike costa
Motor starts right up, but when I open it up past quarter throttle it bogs way down while ridding, the longer it runs the worse it gets. If I just leave it in neutral and give it full throttle it revs up and down.
Bike sat for 3 years,
Installed new plug, cleaned the fuel tank, took it to a shop and had the carburetor gone though.
Picked up from shop, motor bogged down first day and barely got me back to the truck an 1 mph.
Took back to shop after a month I was told it had a bad plug, I told him I just replaced it.
Got quad home and it is doing the same thing!!!!!!!!!
Thanks in advance for your support!
The carburetor has recently been gone through by a shop
By Jeff Comstock
Help a brother four legger out
Bayou300 acts like it's flooding if it's it's in the Alabama sun all day but, I've cleaned the carb. Sometimes it'll backfire even though the timing and valve lash are in spec. Thought it was sticking float but after 2 times cleaning the carb I'm lost. So
Similar Tagged Content
UTV Crap has introduced an alternator kit for the Kawasaki Teryx that quickly and reliably boosts your Teryx charging capacity. With an additional 60 amps, there is no more worrying about adding lights, stereos or heated seats.
UTV Crap Teryx 750 60 Amp Alternator Kit.
Smaller 60 Amp Alternator
Easy 1 Wire Hook Up
2 Cog Style Pulleys for Less Horse Power Loss and Less Stress on the Crank
Heavy Duty Cog Style BeltCustom Billet Crank Mounts
$474.95 Complete Kit Ready to Bolt on!
UTV Crap also has an alternator kit for the Yamaha Rhino for $349.95
About UTV Crap:
UTV Crap sells, manufactures and installs: parts, accessories and suspension kits for all major UTVs. UTV Crap is located in Phoenix, AZ can can be reached online at www.utvcrap.com or by calling 623.934.3070
Introducing the Dash Frame system for the Kawasaki Teryx from Black Rhino Performance. The Dash Frame fits nicely into the middle of your dash, and is designed to closely follow the shape of the Kawasaki Teryx dash. This frame puts your gauges and switches at the same angle as the upper dash for easy viewing of the gauges and convenient placement of switches. The panel provides mounting for 3 2"
Recently Browsing 0 members
No registered users viewing this page.