Quantcast
Jump to content


2010 polaris Ranger Pursuit 400 HO running rough


PKR

Recommended Posts

Neighbor dropped off his 2010 Ranger 400 HO. Said it was missing and backfiring. I replaced the plug as it was carboned up (kids use the side x side for chores and it is only idled around yard) Unit ran great, sent back home and it ran great for about 5 hours of run time and then it wouldn't start. He brought it back and I changed the plug again and it would start but would not run great. Pull plug and it was really wet. I suspect the carb needs cleaning and that is the direction I plan on going unless someone else knows anything about these units. ( I have never worked on one of these).

If you know of something else I should check let me know.

Also I am looking for a service manual for this unit.

Thanks

PKR

Link to comment
Share on other sites

I would go right to the intake and check there first.   My guess would be something is in there or the air filter is breaking apart and small portions are getting sucked into the carb?  Air filters after a while break apart if they are not kept oiled.   Simple stuff first, after that get into the carburetor etc.  

Check for bad fuel, water in the fuel, poor fuel flow. Maybe a bad petcock or screen, all this stuff happens. 

Link to comment
Share on other sites

Frank

Thanks for the reply. I had taken a gas sample from the tank yesterday and it looks good today, no sign of water.

The air filter and everything else looks good. My plan today was to pull the carb but I decided to try to start it first. It fired right up and purred like a pu*** cat. I ran it around the yard for about half an hour and it didn't miss a beat. I'm not to sure what is going on. I'm starting to wonder if the kids are flooding it when they try to start it and sitting out in the cold it isn't clearing itself???

The only difference between it being at the neighbours and being at my place is it is left outside there and is inside my shop here.

I'm going to move it outside tomorrow and let it sit for the day to see what happens.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By Spritee1
      having an issue with the unit when running under a load up a hill or in high gear, seems like the belt is slipping, there is a clapping sound coming from the primary clutch like it releases and snaps back in. i don't think I should have a noise like that. this is a friends unit and he has already replaced the primary twice with the same result.
      not sure where to look next
    • By Johnfj44
      The stock driver seat cushion is separated at a seam. I took the seat apart and found that the material has torn and cannot be re-stiched. I'm trying to find a replacement seat. Any suggestions? Hoping for a used seat but couldn't find one on Ebay.
    • By ethie
      Hi All
      I have a 2012 Coleman 500 Outfitter that keeps fouling out the plug within 10-15 minutes 
      not sure where to start
    • By rgeiser
      View File 2003 Polaris Ranger 400-500 service manual
      2003 Polaris Ranger 400-500 service manual
      Submitter rgeiser Submitted 04/18/2024 Category Polaris UTV  
    • By Charlesbrown
      I’m looking for a top end kit for a Yamaha. I would like to see how well the engine runs before spending $6-$7 hundred on oem. Niche has complete kits from $1-$2 hundred.  Anyone have experience with Niche or similar Chinese companies? 
×
×
  • Create New...