Quantcast
Jump to content

  • Do you own an ATV or UTV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Recommended Posts



Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By NeedsWork
      Hi I'm working on a 1995 Polaris explorer 400 two stroke, and I had planned to put in a new wiseco piston and rings and just hone the cylinder. I think it overheated at some point and the rings did not move freely in the old piston. The clymer manual I'm using doesn't really have much information as far as honing the cylinders on a rebuild, but I've been doing some reading and it seems that some cylinders are plated with some type of chrome or nickle plating but I'm not sure how to tell if it has been plated and if so with what. The Wiseco instructions say that their rings cannot be used in chrome plated cylinders. Any information on this topic would be greatly appreciated. 
    • By Avery_646
      Wondering if a 2018 Polaris sportsman 570 head will work on a 450. I have a 2018 Polaris sportsman 450 and I’m rebuilding the motor in it and wanted to do a 570 top end. Or if I could use my stock head with the kit. Thanks In advanced. 
    • By Arizona
      I have a couple other topics on this Bayou but this one is the reverse lever seal is leaking.
      Talked to the dealer and have no listing on the seal. Looks fairly simple but is the seal installed from
      the outside of crankcase or from the inside before I remove it.
      Next question where can I get the new part? I found these on ebay but not sure if they fit.
      any ideas where to buy it? https://www.ebay.com/itm/Kawasaki-KLF220-88-02-Bayou-KLF250-03-10-Winderosa-822138-Engine-Oil-Seal-Kit/352356942519?fits=Year%3A1995|Model%3ABayou+220|Make%3AKawasaki&epid=209928936&hash=item520a1c42b7:g:ZKUAAOSwx6pYooaN:sc:USPSFirstClass!78006!US!-1
       
       
    • By Hodadical
      I've inherited a 1995 Lakota 300... it has the knob in the center of the handbar to twist to go into reverse, but I've notice when downshifting, you don't have to have the knob turned, it will shift right past neutral and into reverse which is a little dicey if not all the way stopped. I followed the linkage back and twisting the knob seems to actuate the lever on the outside of the trans, the internals just don't seem to care about this. 
      What is the likely problem and how back is it to get to? I've never been inside of one of these transmissions.
      TIA,
      -Rob
    • By Budman
      After purchasing a lightly used 2018 570SP (300 miles on it) I noticed that the display was flashing on and off. I remember reading awhile back that this was a common problem on the 18 model. I can't remember what the fix is. It also turns over slow even though the battery is charged. Anybody know what the fix is on this issue?
      Thanks
      Budman
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...