scrambler500

help electrical problem

4 posts in this topic

I have a 99 polaris scrambler and I'm having problems my lights and panel lights work with the key on and the engine off but when I start my quad the lights don't work I need to get this fixed before next weekend cause I'm going to dumont I've never been there before and I want to be ableto ride out there, so if anyone can help me out it would be greatly appreciated thank you

Share this post


Link to post
Share on other sites
  •  Like what you are reading? Please help us by sharing this content.


DAMMIT!!! Im not good with Electrical.....

Works off Battery....But not with the Bike on................

Nothing.....High or low Beam???

Share this post


Link to post
Share on other sites
  •  Like what you are reading? Please help us by sharing this content.

i found out what the problem was the people I got it from had the voltage regulator wired wrong now everything worksand the circuit breaker was bad

Share this post


Link to post
Share on other sites
  •  Like what you are reading? Please help us by sharing this content.

Good to hear you got it. Good Job!

Share this post


Link to post
Share on other sites
  •  Like what you are reading? Please help us by sharing this content.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!


Register a new account

Sign in

Already have an account? Sign in here.


Sign In Now

  •  Like what you are reading? Please help us by sharing this content.
  • Similar Content

    • By ut1w7b
      I have a 94 sportsman 400. It sat for several years before i got it. I have cleaned the carb it will start and run for about 5 min then it will flood. I have torn it down and cant see anything wrong. has anyone else ran into this problem any hel would be great.
    • By kingjosk12
      A week ago I could not even get close to starting it. But now I adjusted the valves (exhaust valve was not closed). i got it running but would not run without choke. i adjusted the float because it was to low tried starting it up again and it would not even start. So i went back and looked at the valves and the valve was now open again so i adjusted it and it started right up and ran perfect without choke. So i put it all back together thinking it was ready to go. Started it up and let it run for a little bit. i turned it off and tried starting it again there was NOTHING. took it apart and there was 0 compression and the exhaust valve was open again. I am completely lost need help PLEASE!!!:aargh:
    • By dblbassdrumer
      [ame]
      [/ame] only when u pull back in the clutch does it make this noise and wanna take off
    • By BCNemo
      I have a 2001 Yamaha Kodiak 400 (YFM400FWAN©) On a recent hunting trip a problem popped up and I hope someone else has experienced this, so that I can learn from them instead of going on my own hunt for an answer.
      The Problem:
      On cold days (sub 25 degree) I choke the Kodiak and it starts instantly. It revs up and runs on "high idle" without any problem. However when I return the choke lever to its "normal" position the ATV continues to run and a very high idle. I cant put it into gear until the idle comes down, which it doesn't. In order to use the bike I have to shut it off and when I restart it I must place it into gear before the engine gets a chance to rev up. It then returns to a normal idle and the machine behaves normally. This only happens on real cold days but it is a problem I want to fix. Can anyone offer some help?
    • By reich
      I have a 2005 Fourtrax. It wouldn't shift and the display was blinking three times so I replaced the angle sensor. It initially worked, but now the display is blinking eight times. I did not reset the computer after replacing the angle sensor. Do you think I need a new control motor? Anyone else have this issue after replacing the angle sensor? This is a great site. Thanks