Quantcast
Jump to content


1993 Yamaha Big Bear 350. Swing axle rubber boot replacement

skeeter45

By skeeter45
in Yamaha ATV Forum

 Share

Recommended Posts

Mech Grand Master

Mech

Posted
Posted

If the other end of the boot you have is right is right, then that 4KB might be the one.

Looking at pictures I see some boots look like the big end is closer to the small end diameter than other boots..  The 2HR looks like it's big end is quite a bit bigger than it's small end diameter. The 4Kb the two ends look similar.

Probably easiest to ask them what the diameter is before you buy though to be sure.

Link to comment
Share on other sites
mesjeff Newbie

mesjeff

Posted
Posted

Hey guys new here and just thought I'd chime in since I just finished doing this to my 88s . I ordered both boots from Babbittsonline without an issue  . I did notice that on one bike the boot seemed a little more of a struggle to get it to slip up onto the lip of the trans/engine side . but it did go . Now I didn't notice any slack in either boot on either bike but the one I did 2nd I do remember struggling with it a bit more . Is it possible that there is just an overlooked irregularity because it seems that this has  been tossed around in  another forum . 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • jashadams
      2009 Ttr 125le rear shock trouble
      By jashadams
      So I installed a new shock on my 125 yesterday sadly it wasn't adjusted right I took it off to adjust it tried to install it again today and it no longer fits I loosened the nuts on the spring again and it still won't fit idk what I'm doing wrong when I try to install it but I'm lost any tips or videos would be great thanks.
    • newguy024
      New to atvs
      By newguy024
      Just got into ATV riding just last week, never had much money so i couldnt afford to buy anthing, so now at the age of 34 i just bought a 1987 suzuki quadrunner 300 for 500$ took it out a few times and what a rush of excitement to go through that first mudhole haha!
    • HSTAR
      1997 Yamaha big bear 350 Shift shaft issue
      By HSTAR
      Hey I have a 1997 big bear 350 4x4
      I replaced the shifter shaft and the shift arm linkage and the rod when I installed them all I was unaware that you had to line the dot on the shifter shaft with the gap on the linkage arm gap put it all back  together and rode it I can't get it to shift in the right gears  I can move the shift cam by hand and goes in different gears but with the shifter shaft in it riding I can't put it in R or N 
      Anyone know how to line up the shifter shaft and the shift cam s
       
    • ResQ91
      1987 Yamaha Big Bear Electrical Troubleshoot
      By ResQ91
      Hi guys
      My 87 Bear 350 won't start and could use a hand.
      Turn key on and Oil light turns on and then slowly fades out. (I think this is key to this) No start, not even a tick.
      battery and connections good
      A Solenoid post jump turns it over
      Neutral Safety Switch wire attached and seems good
      It has not had a wire/switch on Rear Brake Pedal ever since I had it.
      Any thoughts on some other things to troubleshoot this??
    • utvboard
      2009 Honda Big Red
      By utvboard
      2009 HONDA BIG RED
      Honda enters the MUV (multi-use vehicle) market with a side-by-side machine that leapfrogs the competition to set new standards in utility and recreation. With numerous automotive-based technologies, Big Red features a powerful 675cc OHV liquid-cooled PGM-fuel-injected single-cylinder engine and an automatic transmission with three selectable drive modes plus Reverse, front and rear independent double-wishbone suspension, a roomy cab featuring rubber-mounted bucket seats with adjustable backs, and a specially designed, highly durable, tilting cargo bed. A broad selection of Honda Genuine Accessories will also be offered.
      Big Red
      KEY FEATURES
      - Powerful OHV, liquid-cooled, PGM-fuel-injected 675cc, mid-engine design.
      - Automatic transmission with Reverse.
      2009 Honda Big Red in Camo
      - Three selectable drive modes.
      - Front and rear independent double-wishbone suspension for an impressively smooth comfortable ride.
      - Roomy cab and rubber mounted bucket seats with adjustable backs designed to comfortably fit a wide range of body types and reduce fatigue on long drives.
      Specially designed, high durability, tilting cargo bed
      - Specially designed, high durability, tilting cargo bed.
      - Wide variety of Honda Genuine Accessories.
      - Summer 2008 release. More information to come soon!
      Board Message - UTV Forum - Online UTV Community and UTV Forum

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...