Quantcast
Jump to content


Honda 420 Rancher 2005 shifting problems


sunvalleyfarms

Recommended Posts

Have you read the service manual ? Is the dash flashing ? Have you tried getting the trouble codes out of the dash ?

Are you sure the new battery is good, and fully charged ? Have you checked the charging is charging, and regulating ? Are you sure you didn't momentarily connect the battery up backwards, or try to jump start it but connect the jumpers backwards momentarily ?

When you say it won't shift gears in forwards, do you mean it moves but only in one gear, or that it won't go into any forwards gears ? Just to clarify before I start looking in the books.

And in reverse, it moves ? but the engine runs badly or just has no power ? If the motor is running ok, but has no power in reverse it might be a gearbox/control problem, or it might be an engine problem..

 

Edited by Mech
Link to comment
Share on other sites

  • 5 months later...

Bummer when someone posts a question and members take the time to reply and the OP never shows up again.
Thanks @Mech for posting so much on the forums and helping others out. I am new here but looking forward to peruse the forums here and there and learn how to better service my own ATV from other people's problems and solutions and perhaps with time and more experience contribute back.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By HSTAR
      Hey I have a 1997 big bear 350 4x4
      I replaced the shifter shaft and the shift arm linkage and the rod when I installed them all I was unaware that you had to line the dot on the shifter shaft with the gap on the linkage arm gap put it all back  together and rode it I can't get it to shift in the right gears  I can move the shift cam by hand and goes in different gears but with the shifter shaft in it riding I can't put it in R or N 
      Anyone know how to line up the shifter shaft and the shift cam s
       
    • By hardcastle
      My friends KQ 300 starts fine and runs, as soon as you put it in gear and try to accelerate its bucks and farts like crazy, not moving... I cleaned carb and it worked good for 1 day... now back to same problem.... could it be such as a bent valve????
    • By DarkRider
      This is something I'm extremely curious about. Has anyone ever attempted to buy a quad (or any other vehicle) from an impound lot? I've always wondered if this could be a bargain, or a waste of time. Google searches do turn up some helpful results. Looks like the state of NJ holds auctions online which I'd be a bit hesitant about.
       
      My online searches haven't really turned up any results of anyone buying an ATV this way. I'd be really curious if anyone tried this, or knows someone who has. I've actually found a couple pages with online auctions for my state, but none had ATVs.
    • By jashadams
      Hey all back again with my 1989 moto 4 250.
      After putting a new carb on it it's really sputtery, it has new gas and I'm wondering what to tune on the carb to make it idle better. I've attached a video to describe the issue more. The bike is still work in progress but I think the video gets the point across. Thanks!
      Snapchat-1142015191.mp4
    • By p5200
      I'm assuming, it's alright to test the engine after adjusting valves without the rear axle installed? Can someone please verify this? I'm waiting on axle parts and wanting to get that done while waiting. Thanks! 🙂
×
×
  • Create New...