Quantcast
Jump to content

Recommended Posts

Posted (edited)

Problem number 1,

2000 Polaris Xplorer 400.  No start, has spark. Has fuel ,found Low Compression less than 60 psi.  What to do next?? Going crazy here.  

Problem number 2. 

1994 polaris Sportsman 400 starter won't engage.  Button on left side with  light switch seems to be almost stuck in, weak spring behind button?

 

Any help would be nice.

Thanks Chris in West Central Minnesota

 

 

Edited by en4cer
Miss spelled words
Posted

On the 2000 i would add some oil to the cylinder recheck the compression if it goes up its rings if it does not i would look into a valve problem.

On the 94 you can take the button apart make sure its making contact when you press it, or just replace it.

Posted

On the 2000, figured i would look into rebuilding the top end . Play it safe if the oil trick doesn't work.

On the 94 am looking into finding a spring for the starter button.  Another issue before the starter issue, I think the stator is bad,  I did not see a jump in the voltage at the battery when it was running while using a multimeter,  even. Revved it up, no change in voltage either.   

 

Thanks for the input

 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Popular Now

  • Similar Forum Topics

    • By realpilot
      I am unable to find a wiring diagram for this UTV.  When I turn the switch to on, the contractor does not engage.  The Brake pressure switch and the parking brake switches work correctly. What else should I be looking for?  All of the diagrams I have found are for newer models and the wire color coding is different.
       
      Thanks
    • By 88bigbear
      Bought a 88 big bear 350 4x4 took it for a run and lost spark, found it was stator so I replaced that then took it for a long run and it sat for 2 days and no spark again, this time stator tests good on ohms and voltage for source and pick up coils so I started replacing things including regulator, ignition, ignition coil and plug cap, spark plug and everything tests great including all safety switches until the orange wire for ignition coil from the cdi it only reads 3 volts so I replaced the cdi and still 3 volts, any ideas??
    • By cfherrman
      Fixing for a friend. Atv was at a different friends house to be fixed and he rebuilt the carb and had it running nice, then it shut off and no more. He replaced the key and the coil.
       
      So he got busy, so I am helping, I checked the wiring from the stator to the cdi, and from the cdi to the coil. All is good. I checked resistance on the pickup coil, good, and on the source coil, open. I buy a new stator (China) and the 4 prong plug only has 3 wires in it while mine has all 4. I checked resistance in the source coil and it's in the 300's. I pulled one of the old pickup wires out of the old stator and wire it in the new one. Still no spark.
       
      Why do the wires differ, I checked the VIN again and it's "J" for the year and I got a 1988 stator. Please help!
    • By LashinWheeler
      Hello all, I have a 2006 Polaris Sawtooth with no spark. It has a dead battery but with a jump pack on it, it will still not Spark. Plug is good, Throttle ETC is not closed, Stator pick up coil seems to Ohm out in the correct range, Unsure how to properly check the CDI. And when ignition is on the Neutral and reverse light come on but after cranking just the neutral stays on. 
       
      Any help would be great,
       
      Thanks!
    • By logray
      Hi all, 

      I am wondering if any of you have a Clutch Starter gear from a 1988 era quadrunner 250 sitting around that you could get me a precise measurement of the outer diameter of the race the sprag engages onto, for me? I need to machine a damaged race down and install a hardened sleeve and need that measurement (it's on a different gear than the OEM one, so I can't buy and use a OEM gear). 

×
×
  • Create New...