-
Do you own an ATV or UTV? Join our Forum!
Join QUADCRAZY ATV Forum today for FREE! We keep these forums clean and user friendly. All first posters will have to wait to have their content reviewed and approved. Once your first post is approved, you will no longer need to got through an approval process. To gain immediate approval and a NO ADS experience, consider subsribing to our Premium Membership.
-
Similar Topics
-
By Atvguy0901
Thank for the add on quad crazy. I am new here and need some help with my atv. It’s a older Yamaha Timberwolf 250 that I purchased second hand from an person. I got it home ans started to look into it. He stated it needed a cdi box so I ordered one for it and a battery as well also a key switch cause it did not come with one. I put all the parts on it and when I hit the start button it just clicks and noting else. Thank you any help is appreciated.
-
By Gwbarm
Still working on the 2000 Big Bear with a no spark issue. A lot of this has been covered in an older thread, but I will summarize.
Bought it with the previous owner telling me it needed a new wiring harness, but the wiring harness was in tact and seemed to be fine, except starter solenoid and coil was missing, also the engine was stuck, and no spark plug. Got the engine free and rotating, checked compression, it was 130, not great, but good enough to run. Hooked up a battery, nothing , went through all the wiring and found starter cutout relay bad, replaced that, now I have it rotating with starter. Pulled the plug checked, no spark. Checked start/stop switch, working like it should, reverse relay was bad ,replaced that. Checked continuity from coil to CDI, good, checked pickup coil resistance, within specs, checked anti kickback coil resistance, within specs. What am I missing.
-
By EugenM
Hi, I have a grizzly 600 from 2000 that has been giving me headaches for a few days. it has no spark. I checked everything I could according to the manual and everything was within the parameters and I came to the conclusion that I need to replace the CDI .... when I did the measurements I did not check if the orange cable that goes from the CDI to the induction coil has a connection to ground (I just checked if it had continuity and it did). after I put a new CDI and I still had no spark, I saw that somewhere under the fuel tank there was a bunch of cables that were a bit crushed and there that orange cable was stripped and had a connection to the chassis. what are the chances that the new CDI will be fried because of this?
Thanks!
-
By allonmorris
Hey guys,
I have a 2002 yamaha wolverine that needs a new wire harness. Does anyone have a clue where i can get one new or used. ive looked all over and cant find much on a 2002 model.
Any help will be greatly appreciated.
Thanks in advance!!!
-
By reprob
Im new to the group and hope to find some help here. I have a 1997 Yamaha Big Bear 4x4. I am having ignition issues. I have checked all switches to the CDI box and all check out. I Replaced The pick up coil and stator, as the pick up coil was open, no continuity. My problem is I can't find a schematic that matches what I have. My CDI has 2 plugs one 4 pin with 3 wires going to it, and the other is an 8 pin with 7wires going to it. I have traced all but one it is solid blue on the 8 pin plug. I have no idea where it disappears to with out tearing apart the harness. Any ideas as to what this wire goes to? A pin out of the cdi would be helpful, The number on it is F8T32372. Any other ideas before I try and find a new CDI. Thanks for any help. Robert
-
-
-
Similar Tagged Content
-
- 7 replies
- 3,757 views
-
- 5 replies
- 6,378 views
-
- 1 reply
- 4,080 views
-
- 2 replies
- 2,178 views
-
- 3 replies
- 2,472 views
-
-
Gallery Images
-
Recently Browsing 0 members
- No registered users viewing this page.
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.