Quantcast
Jump to content

Recommended Posts

Posted

HAve 2005 Cat 500. It has been sitting for about 10 weeks, and will not statrt. Cranks good has new battery, but will not fire up. I got all old gas out and put fresh in, but no good. If it has a choke or primer i can not find it. It only has 270 miles on it, so not a lot of expierience with it. Always has some trouble starting cold, but catches eventually, noit this time. Also, small protrusion under carb lesks fuel when running, just idle i think, but not positive. It looks like there should be a hose coming off of it, but dont think so. I cant figure it out. Nearest dealer is 33 miles away. Any help sure would appreciate it!!!!!!

Posted

Im not a mechanic, but I am pretty handy and have lots of tools. Is this somthing that someone that is mechanically inclined can do on there own? Are there any reference guides out there to help with instructions on how to? How is the carb mounted?. Thanks to DirtDemon for the info u gave me so far?

Posted

Agreed. It does need to be cleaned because you have some dirt under the needle. These carbs are prone to this problem. You'll need some carb cleaner and compressed air. You can do it yourself if you pay very close attention to where the parts go when you put it back together, otherwise I'd recommend taking it to a shop. Also, install an inline filter before you run it again. I had this problem with my 400 before I installed the filter, now it's been years since it's leaked out the overflow.

Also, you'll see a little lever on the side of the carb with a hole in it. That's your primer. If it sits for long periods of time, especially in cold weather give it 3 or 4 pumps before you try to start it.

Posted

found primer, but no go. Found line coming from fuel tank where it goes to what i think is fuel filter under seat, then 2 lines go from it to carb. Pulled lines and they were DRY. Had to inject some fuel into line to carb to gwet it to start. Has this happened to anyone before. Once started, it still pours fuel from little nipple(overflow?) under carb though. Is this because carb still need clean. Is round thing under seat with fuel lines to and from a fuel filter? Thanks to all who helped!!!!

Posted

Yes, it sounds like the carb still needs to be cleaned. If you are mechanically inclined, you should be able to figure it out if you just dig in and take the carb out. Once you have it out, take it completely apart and clean every part and passage and remove any residue in the carb. Pay special attention to the float stopper and the seat that it sits in, debris in this area is likely the reason that gas is leaking out of the carb.

Posted

Yes, that's an overflow drain on the bottom of the carb. You have a piece of junk in there keeping the needle valve from closing when the float level rises to shut the needle valve. When it doesn't shut off the fuel it will overflow from that drain, and run down onto the motor (been there).

Yours is a 2005 you say. Where is your gas tank located? The fuel filter would only have one hose in and one hose out (just a little cylinder with nipples on each end). It sounds like you're describing the fuel pump, provided the tank is under the fender instead of ahead of the seat. This type of fuel pump operates off vacuum impulses to draw gas from the tank to the carb. The ones with the tank ahead of the seat don't need a pump, gravity takes care of it.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By LMI
      Hi all.  New to the forum & quads.  Seems like a great place full of info.
      I just recently picked up a 2005 Suzuki KingQuad LTA700.  I need a battery.  I've been reading up on conventional vs AGM types.  I have a Royal Distributing and Canadian Tire.  RD has 2 types avail for my year/Model a battery YTX16-BS CRANK $75, and BATTERY YTX20CH-BS YUASA $140.  Neither of these is the type from the manual FTZ16-BS.
      from what I can tell... I think the only difference is the capacity with the $75 unit rated at 14 AH/10HR and the $140 unit rated at 18 AH/10HR ... which is the rating in the manual for the FTZ16-BS.  How much does this make a difference for nearly x2 the cost?
      And about the models/type numbers.... what is important to know ... they all end in "-BS" but are the other details relevant or just manufacturer naming?
    • By tds7
      The battery on my Big Bear drops completely down in the battery compartment nothing sticks up to grip too, plus there is only 1/8" clearance along the sides, no way to get a grip on it to pull up out of battery compartment. I thought about putting a piece nylon strap under the battery and leaving enough up each side to give me something to pull it up out ff the battery compartment or using a big zip tie around the battery.
      Any others have any ideas or have had this issue. 
       
    • By Jason39
      I’m having a issue with my choke when its on it runs fine when I cut the choke off the atv cuts off went to take the carburetor off and saw the choke plunger broke at the nut to screw it in could this be my issue? Do I just need to buy a plunger kit and put it on? I took the carburetor off and cleaned both jets anyway just to make sure and it’s still having issues staying on
         
    • By hunky
      This old boy has been coastal so lots of rust. But when I turn the key, nothing. Green neutral light works, head/tail lights work. Was running fine when I parked it for a few months.. no issues with starter. This did happen once before (last year).. not sure what overcame it.. maybe playing around with gear shifter.. but not sure if that was what did it. But doesn't seem to do anything now when I play around with it while hitting the start button.
      I did take apart the handlebar mounted start button housing and looked it over. Couldn't figure anything out there, but looked the same as when I had the problem last year. Put my probes on various wires there but didn't learn anything.. not sure how it is wired.
      So this first image there is a connector with 2 wires coming from forward (the male part of connector) - one blue and one blue w/ red stripe. The blue continues down to a post near where the gear shifter enters the housing. (Second image). I was wondering about that.. I opened up the connector and the 2 wires (coming from forward) show continuity when I put my probes on 'em. Thought that was weird, but maybe supposed to be like that? I turned on the key and tested for voltage but didn't find any.
      I'm just unaware of how to test for anything. Would be interesting to put 12 volts to the starter, but not sure about doing that or how. The wires going in are kind of hard to get to. I suppose I could take out the starter.. but wanted to ask if there is something easier to check first.
      Thanks for looking!
       

    • By sunn
      Anyone with experience on relocating the miniscule battery from the front lower center wheel area to the left rear wheel area on the Polaris Sportsman 570?
×
×
  • Create New...