Quantcast
Jump to content

  • Do you own an ATV or UTV? Join our Forum!

    Join QUADCRAZY ATV Forum today for FREE! We keep these forums clean and user friendly. All first posters will have to wait to have their content reviewed and approved. Once your first post is approved, you will no longer need to got through an approval process. To gain immediate approval and a NO ADS experience, consider subsribing to our Premium Membership.

Get your NASCAR picks in before the race!


Recommended Posts

  • 3 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

  • Similar Topics

    • By JacobL
      I cleaned the carb took it a part let it set for 3 hours And I put it back in and was leaking gas out the overflow tube fixed that now it starts but only with choke on and runs rough turn the choke off it dies idk what it is 
    • By remnar
      New member here,
      I have searched here and other places and have not found an answer to my problem.   As the title says I have a 2014 420 Rancher that recently started having an issue were the revs before the clutch engages.  
      I have checked the oil level (per the service manual) and replace the Valvoline ATV 10w40(less than 5 hours) with 10W30 GN4 for good measure. I have used the "pin" method to pull a DTC.  I shows a 8-1 which is a TPS error.  This makes some sense, as if the computer doesn't read throttle position correctly, it could have this symptom. I have checked the source voltage, and tested the TPS off the quad with a Fluke and a power supply at 5v.  It is smooth and does not seem to be a bad sensor. I am confused by the DTC, because the PS light blinks the code, not the check engine light.  However, there are no PS codes of that value.   This condition appeared after a couple days of driving in the cold (~32°) and driving though some water/bogs.   
      A couple questions.  First has anyone seen this issue, and do you have any suggestions? I have followed the troubleshoot right up to the point of replacing the ECU, which I don't seem to have one on the shelf :)
      Second, anyone used a OBDII reader with an a 4pin adapter to pull codes?  If so, what system do you use?
      Beyond the rev issue, the quad runs and starts perfectly and when it decides, the clutch grabs tight (no slipping)
       
       
    • By Yammy
      Can you ride your quad on the road or cross a road if your quad is licensed and registered and you have functional signal lights and running lights?
      Let me know, I'm new to this.
      Thanks! 
    • By Gwbarm
      I have a 2007 Suzuki Eiger with camouflage finish. Over the years the finish has faded to a blue green color, its not as annoying as some that I have seen that faded to purple, but I still don't like it much. Im sure this has happened to others on the forum. Just curious what you guys do to fix this. I was thinking of mixing up some clear with a hint of yellow in it to neutralize the blue green but will have to do some testing to get it right. Any ideas would be greatly appreciated.
    • Dream Car Giveaway
    • By slide187
      So I changed out the steel winch cable on my CForce 800-2 to a synthetic I had gotten when I had my old outlander and just never put it on. That wasn’t too difficult but I had to open up the hole in the spool a bit to get the tail thru. But I got it thru put the set screw back in and wound it up. It’s one of those Amsteel type cables, 50’ with an 8’ sliding protection sleeve on the hook end. And I put on an aluminum hawse with a rubber stopper and new hook. (Which is like the Warn Epic hook. Might be a little big. Haha ¯\_(ツ)_/¯)
       

       
      And right before that, I pulled out the halogen headlights. Replaced them with these nifty dual color LEDs. (But because of the heat sinks on them I had to widen out the holes for the bulbs a little and then vacuum all the dust out of the light housing with an improvised headlight vacuum. Haha)
      But they fit and the lights are yellow on regular beam and high beam switches them white).
       


       
       
      Sent from my iPhone using Tapatalk
  • Gallery Images

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...