Quantcast
Jump to content


2003 Kawasaki Bayou 250 No Start


Recommended Posts

Hello, I am new to quadcrazy looking for help with a 2003 250 Bayou I just bought. It has no fire. When I switch it on I have no netural light or any light. The battery is fine and the starter turns fine. No fire at plug. however when I kick start or use the elactric starter the netural light lightes breifly. I dont have a service manual. So I dont know where any fuses might be located. Does anyone know a site to download a pdf manual? I have gone online and found free pdf manuals for foy two Honda four trax. Thanks any on that can tell where to start of how to check the fire. Thanks Mike

Link to comment
Share on other sites

I would try changing the plug because it can cometimes be a bad plug and then see if the plug sparks to a ground when you try to start it. There may be a problem with the neural switch and that may also keep it from starting depending on the year. You might be able to adjust the linkage to get the nutural light to turn on. Newer models will start in gear if the brake is locked but it may be a bit too old for that.

Link to comment
Share on other sites

Hello Thanks for your respones. The starter will not turn the motor over from the starter button. When I switch on the key I get nor netural light at all. I can take a screwdriver and make the starter turn the motor by jumping the starter relay. Wher I do this the nutural light will light while the motor is trying to start. However I have no fire at the plug. . Where is the nutural switch? I have been told there may not fire due to the CDI. Thanks to anyone who can futher give me some advice.

Link to comment
Share on other sites

  • 2 years later...

first, I new to site, I need to ask same questions. Not sure where to oust mechanical question my 250 bayou will not start. first the electrical switch start would not start the bayou, now pull wont. changed plugs. last start was pull off start with truck. now no start am I am not strong enough to pull start anymore. when I hold down compression lock the engine turns ok, I have bought new battery, plug. air filter, when I push start switch I do get the solenoid to click, and I cave good compression kick back from engine it seems, any help is appreciated.

Edited by grandpa
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By newguy024
      Just got into ATV riding just last week, never had much money so i couldnt afford to buy anthing, so now at the age of 34 i just bought a 1987 suzuki quadrunner 300 for 500$ took it out a few times and what a rush of excitement to go through that first mudhole haha!
    • By justent_88
      Hello, im looking for some input on this situation i have. My 94 Mojave has no spark, and i have no idea what it is. Ive replaced/tested the magneto, the pickup coil, cdi, the ignition coil. Even the key and Killswitch. I haven't tested the harness its self, but i have tried another harness and still nothing. The only thing i can think of is the fly wheel itself. I have found a lot of metal shavings in the fly wheel and have cleaned it the best I could. But nothing happened afterwards. I am truly stumped here and hoping some of yous could shed some knowledge/ideas that could help get this thing to fire. 
    • By cavry
      Wiring shows White and Brown to solenoid blades. Then a black wire from starter circuit relay to solenoid. I am confused,  where is that black wire supposed to connect?
      Thanks for any help
      Cavry
    • By HoldenBoy
      Hi all,
      Looking for some help on a starter/bendix issue. Can Am outlander 450 2017. While cranking to start, the starter spins and engages into the ring gear. After a few seconds the bendix retracts while still spinning and there is no damaged teeth on the drive pulley.
    • By Mhatayas
      What should I do about this , bad oil leak where the filter cover bolts on . Can I use some gasket maker 

×
×
  • Create New...