Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Recommended Posts

Hi, newbie here and desperate for help !!

I have a Apache RLX100 Quad and for some reason it wont pull when being revved, if you lift back wheels up then rev the wheels fly round but put pressure back on wheels and it wont pull. I have fitted a new clutch and gears but it hasn't:aargh: helped

Any advice is much appreciated :biggrin:

Share this post


Link to post
Share on other sites


rollers and weights????

The clutch system was changed completely along with the gears, if it helps its a rev and go

thank you

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Steve Howard
      Ran find shut down the quad next day would start and idle when you try to accelerate it would start popping through the carb got a rebuild kit soaked it in chem clean after break down for 12 hours on slow vibrate reassembled and adjusted per manual still the same thing any help would be really appreciated thanks and happy ridding  
    • By Gilbey
      Does everyone run the tire pressure as stated on tires or perhaps a couple # below to soften the ride a little?
    • By Dwight Williams
      Ok, so I bought this scream of a deal the other day - a 94 King Quad 300 for $40.00.  It's been sitting outside with no carburetor on it for about a year.  Its rusty, missing some parts, wiring is all cut up and spliced etc.  No seat, no racks but the plastic is all there minus the headlight housing.  Anyway, who can pass up a $40.00 quad right?  I get it home and looked at the sight glass for oil level, it's about 1/2 oil and 1/2 water.  I drain it, refill it and turn the motor by hand (recoil starter is missing) and it turns over just fine.  I worked on the wiring for about an hour and got it to turn over with the electric starter and got enough of it sorted out to get a spark.  Did a quick compression test, 70 lbs.  Wet test bumped it up to 90.  Ok, so rings and cylinder washed out with water for a year, not too surprised.  I thought 'what the hell' and sprayed some starting fluid in it and it ran for about 2 seconds - enough to show  it's got life.  Since then the compression has gotten worse, I can't get enough pressure to activate the carb diaphragm, therefore no fuel pump either.  The compression is now around 60.
        Anyway, my question is....is it worth it to try to get this thing going?  I tore the top end down today and the cam and one of the rockers is pretty worn.  I figured a top end job would be about $100 or so, depending on the condition of the cylinder but I'll probably have to put a cam and rockers in it as well.  Doing some research on ebay I figure I'll have to spend about $500-$700 to make the whole machine right again.  Much less just to make it run and use as-is but I won't really like it until it's right.  I don't mind doing the work, I actually enjoy it but I'm concerned about what all that water did to the rest of the internals, I can't really test it all out until I can make it run.
      I know it's a basket case but I'm not into it much at all, even if I do the top end and find something else wrong I'm still not out much.  I'm leaning toward ordering the top end parts and going from there unless you can convince me otherwise - any way to check the rest of the internals without tearing it down?  I plan on flushing the oil cooler before I do another oil change, I've drained it twice now and it gets milky almost immediately just turning the starter - I suspect the oil cooler is polluted badly.
       
      I'll get some pictures today if anyone want to see them.
       
      thanks!
    • By MarkinAR
      Have any of you fine folks used coil spring spacers to lift an ATV? Ole 93 Kodiak could use a smidge more lift and they are cheap enough. Might ride rough but that's ok cuz the shocks are toast anyway. 
      Thoughts?
    • By Skhot K
      Hello! I picked up a YFM400 and I would love to talk shop with knowledgeable co-owners, and I'd love input about the machine from anyone here who clearly knows more than I do! Cheers from NY
  • Similar Tagged Content

    • By Aaron Skinner
      Hi All...
      ok ive brought my son a Apache 100cc quad bike ans it seems to have a spark issue..
      When i got it i couldnt get a spark then i messed around with it and got a spark and got it running, then it just died after 30 mins, now no spark so i replaced spark plug, ignition coil, cdi, ignition switch, stator and regulator and got a spark again now its gone again? 
      Ive check the wiring to see if any loose connectors, cant start by electric start because the starter clutch is broken so can only kick start it and thats a pain as it sometimes slips ( needs new teeth on it)
      the kill switch us 2 wires that are just loose no switch anymore as it broken and the other wires i think are for the lights and the electric start lever which is now broke
      Im crap with electrics so not sure how to trace and test
      also my new stator has 6 wires instead of 5 so i am unsure how to wire it, see pictures of mine the correct one and the other off ebay which they say to re-wire
      any help with this guys?



    • By ApacheRancher
      Hi !
      I ride a 2008 Honda TRX420FM. My next mod (just installed license lights, horn & mirror to make it street legal) is to make a new large dash like the Dakar Rally bikes.
      Lisa
      Apache Junction/Roosevelt Lake
    • By kie1989
      Hi there I've recently bought my lad an apache f100 and I want to tune it for him not to sure the year think it's 2008 what best thing to do and where to get from also could do with more info about these.


  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...