Quantcast
Jump to content

  • Do you own an ATV, UTV or SxS? Join our Community Forum!

    QUADCRAZY ATV Community and Forum are FREE to join! We keep our ATV, UTV, and SxS forums clean and user friendly. All first time posters in our forums will have to wait to have their content reviewed and approved. Once your first ten posts are approved, you will no longer need to go through a forum post approval process. To bypass the approval process with immediate access and a NO ADS experience in our ATV, SxS, and UTV forums, consider subsribing to a Premium Membership

how do i pull counter shaft collar from yamaha warrior


Recommended Posts

My 2002 warrior needs new countershaft oil seal but the kit came with a collar also. I can pull the sprocket and old oil seal out but how the heck do I get a grip to remove the collar from the shaft? I can't find a how to anywhere online. Any help would be great.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By HSTAR
      Hey I have a 1997 big bear 350 4x4
      I replaced the shifter shaft and the shift arm linkage and the rod when I installed them all I was unaware that you had to line the dot on the shifter shaft with the gap on the linkage arm gap put it all back  together and rode it I can't get it to shift in the right gears  I can move the shift cam by hand and goes in different gears but with the shifter shaft in it riding I can't put it in R or N 
      Anyone know how to line up the shifter shaft and the shift cam s
       
    • By Lafytafy
      should i run a thicker oil in a older quad because it make a little more noise than usual 
    • By Suzukiquad
      Hi, I have been around everything with a motor since I was little, and finally purchased more to get my husband, and kids involved. I have 4 quads I will be searching around for information on. I have two 2002 Suzuki LT80K quads, a 1997 Yamaha Timberwolf 250, and a 1996 Kawasaki Bayou 220. I have had different ones throughout the years, and plan on buying another Yamaha Banshee. I plan on trying to learn more about all of them, so I can customize some of them. I know nothing about them besides how to race them, my dad always took care of the rest, but figured it was time for me to learn. 
    • By kiriyaaoi
      Hello everyone, I just picked up an 02 LT-F250F the other day and have been in the process of tearing it down to fix some stuff- one of which was the cylinder base gasket leaking like a sieve. Well, I know why that is now, and I also discovered that someone had been in there before. I didn't take pictures, but it looks like it was probably run low on oil at some point, the cam journals and the "bearings" (for lack of a better term) in the head and the valve cover are totally wiped out, very deep grooves.  From what I know it's very difficult to repair aluminum in this way, so I'm trying to figure out where to go next.
       
      1. Have someone grind down the head and valve cover and fit actual bearings in since the aluminum is screwed, and have the cam ground down to match.  I have no idea what this would cost.
      2. Buy a replacement head+cam+valve cover.
       
      #1 I was hoping someone might have some advice on, but #2 seems like it'll (probably) be the more cost effective option.  However I'm running into some difficulty, it seems like the 2001 and 2002 models specifically use a different head part number,  11100-19B10, instead of  11100-19B01 like for all earlier models.  What exactly is the difference between them? There are obviously far more of the earlier heads because it ran for over 10 years.  Are they actually interchangeable? I've also noticed there are heads from the LT250EF that has 4 valve heads but also otherwise look identical.  Would those work as well possibly?  I'd like to not have to drop $500 on machine work or new heads on a $1300 quad that I'm already putting a bunch of new parts on.  Oh, and it has a new piston and the cylinder itself looks pretty good too, as I said someone was in here before me.
       
      Any help or advice would be greatly appreciated. I'll post pics of the carnage tomorrow.
         
       
    • By alexwv1863
      I have a 2016 Arctic Cat 500 and recently noticed some oil leaking on the engine block to the right of the oil filter. It's near two metal lines going in and out of the engine block. I think one of the lines is called an engine oil line. I have a photo I'm going to try and attach. Any help would be greatly appreciated. I don't want to start tearing into the engine if I don't have to. I think maybe a gasket or something blew around one of these lines. The ATV runs fine otherwise. Doesn't overheat or anything.

  • Similar Tagged Forum Content

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...