Quantcast
Jump to content

Recommended Posts

Posted

i have a kazuma falcon 150 it was running good for a while but lately it has been hesitating and now its not but its so slow now. i can have the throttle full but it barely moves. what could be wrong?

Posted

there is probably a clutch adjustment. you could try that. it has the revs? on mine it is on the throttle side of the bike, it looks like a slotted screw inside a nut. not sure left or right on yours to adjust more, but once tight, back off half a turn ...

Posted

Thank you for the reply. I can have it in neutral and rev it and it revs high but drivin it's slow. Do you have any pictures of it? I'll google it and see if I can't find it thanks

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Popular Now

  • Similar Forum Topics

    • By HoldenBoy
      Hi all,
      Looking for some help on a starter/bendix issue. Can Am outlander 450 2017. While cranking to start, the starter spins and engages into the ring gear. After a few seconds the bendix retracts while still spinning and there is no damaged teeth on the drive pulley.
    • By 97kingquad
      Okay so I bought this 1997 sazuki king quad from a guy and he had it for a few years. 
      He had it registered and on the trails last year but he said it bogged and backfired when he would try to drive it. so it sat for a year. 
      I bought it for 800 bucks and got it running that night and it ran great for a few days 
      But I parked it the other night and went to start it again and it was really hard to fire up and when I did it was bogging and idling high then low again.
      So I took the carb out and cleaned it (ended up doing it twice because it was still doing the same thing) 
      Now today I have it running slightly better, but it is still like 20% 
      I have been looking it up and trying to figure it out but I can't find the issue, has anyone else had this problem? I'll attach a video of it running and giving some throttle 
    • By PupATV
      Hey guys! I am new here to the forum and need some help getting my Polaris 325 Magnum 2001 Running.....So I got it for free and it has never run quite right...I put a aftermarket carb on it last year and it was running fine but it only went like 20 maybe 25mph max......But then the needle and seat sealed leaked within a yeah and it flooded it REALLY bad so I changed the oil because it was full of gas. So then I put a genuine Polaris carb on it and I have it set to all the factory specs, but it was still not running right....So I replaced the ignition coil and the spark plug and that solved one of the problems I had (It would bog down and stop running when i would go up a hill) But it still didn't have that much "Punch" to it like my Kawasaki Prairie 300 ans Suzuki Kingkuad 300.....So I replaced the CDI but it's still not running right! It's acting like it rich kinda....So it runs mostly okayish when I have the airfilter on but the top of the airbox off but as soon as I put the airbox lid on it like REALLY bogs down and wants to stall really bad. I have the carb at the factory specs and it has a pretty new fuel pump so I have no ideas whats going wrong! It still nly has a top speed of only about 30-35mph and it sounds like it's choking the whole time! Thank you for sticking to the end, and I hope you guys can help me!
      -PupATV
    • By bhristianzx12
      I have acquired a free 92 Polaris 350L 4X4. Ive replaced carburetor from ebay, replaced spark plug, im trying to pull start but sounds like it doesnt want to fire. Spark is a bright orange spark (checked with spark plug tester), replaced plug, pre mixed gas from an external gravity feed tank. Compression test good. Anyone got any recommendations for me?
    • By carkivey3
      i just picked this up. was told ran fine but overheating issues led to replacing head gasket and head. has not ran since. he is not a mechanic but helped someone else who he could not get back to finish job, got aggravated and put up for sale. i was thinking timing issues. i have 110-120psi on all 3 cylinders so i think valves are correct. dont know about distributor yet. however i have no spark. i have no power going to ignition coil. tried to follow white wire but gets lost in wire harness. does anyone have a wiring diagram? can anyone tell me what conditions have to be met before starting. motor turns over so i would think all safeties are met but you never know.
×
×
  • Create New...