ltz 400 wont stay running
-
Similar Forum Topics
-
By joezee13
After turning off engine in neutral starter wont engage If I rock unit back and forth it engages Getting progressive worse.
-
By middlebrookgt
Hi All. I introduced myself some weeks ago with my 2006 LT-F400F that needed a list of repairs including replacing the cracked generator cover. It is back together as of last night and cranks up, idles and revs high pretty well. Needs some fine tuning and stop backfiring at stop.
The big issue is it will not go into gear. I reassembled the insides with help from y’all’s posts. The transfer selector moves from H-L-R, and the foot shifter moves thru the gears and finds neutral easily enough. Before I tear it back open, the transfer selector on top does not move as far as the repair manual says. The diagram shows the shaft moving something like 40 degrees between L and H and 50+ degrees between L and R but it doesn’t move that far even though it finds the indent areas and moves well.
Could this be the problem. I aligned all the dots on the shifter gears inside and it appeared to not be binding anywhere. I do hear the gears touching when I shift like they are trying to engage, but zero movement from the ARV
It was somewhat difficult to tell whether all the parts are installed on each shaft.
Are there better/bigger photos somewhere that would allow me to be confident I included all the washers and bushings, etc? If I had any doubt on parts that were laying inside after the cover broke then I purchased replacements from online stores.
TIA for any input or feedback!! Pics are from when I first took the generator cover off.
-
By 97kingquad
Okay so I bought this 1997 sazuki king quad from a guy and he had it for a few years.
He had it registered and on the trails last year but he said it bogged and backfired when he would try to drive it. so it sat for a year.
I bought it for 800 bucks and got it running that night and it ran great for a few days
But I parked it the other night and went to start it again and it was really hard to fire up and when I did it was bogging and idling high then low again.
So I took the carb out and cleaned it (ended up doing it twice because it was still doing the same thing)
Now today I have it running slightly better, but it is still like 20%
I have been looking it up and trying to figure it out but I can't find the issue, has anyone else had this problem? I'll attach a video of it running and giving some throttle
-
By Ejwill
I rebuilt the top end on my 2007 Honda Trx500fe. It ran fine right after the rebuilt. But now when I try to crank it it blows Bach through the carburetor. I held my hand over the opening for the intake air and it blew gas back on my hand. Can figure out what happened all of a sudden. It was cranking and was able to ride it running through all the gears. Now can get it to crank just blowing gas back to the air filter. Need help again. Starting to think I should have walked away from this one.
-
By Need-help-with-quads
So I picked up a 1995 Yamaha warrior a while ago and it ran decent with quite a bit of power, I was able to wheelie like nobody’s business, but I noticed that the air filter box lid had bunch of holes drilled in the top and hole in the side, also the air filter itself was serving no function and there was a huge rip in it. So I got a new air box and new filter and when I installed it, the quad lost all power and acted like it was cutting out for split seconds at full throttle. For reference I think it was running rich before because it would backfire a lot so I think it’s just restricting air flow, but how would I adjust to that because I tried leaning out the carb as much as I could but it didn’t seem to do anything unless I put the other airbox lid on with the drilled holes.
any help would be much appreciated
Also even when I put the old lid on, it seemed like just the new air filter gave it enough restriction that it still wouldnt run right
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.