Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

mirack

Squeak from front end Big Bear 400 4x4

Recommended Posts

Coming from front left tire, only when going forward, when in reverse no noise at all. Not a bearing I checked it all out, suppose just needs some grease?

2000 Big Bear 400 4x4.......

Share this post


Link to post
Share on other sites


Sounds like that. My fourtrax does it all the time. Grease it back up and good to go, may wanna look at CV boots, when the squeak gets really bad you probably have a slashed CV boot. Skid plates cut mine to pieces

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Tagged Content

    • By Wali
      I was riding my 400ex one day and when i shut it off to put it in the garage i tried to start it put again to drive it into the garge and it wouldnt start.I put a compression tester on it and its like 30 psi with out throttle and 0 psi WITH THROTTLE.
      when i put my finger over the hole it fell likes its pulling my finger in more then its pushing it out 
       
      Has good spark.When i took it into the shop the said it had 1oz of oil in it and a tiny pit of metal shaving(TINY BIT LIKE 30 flakes)
      When i try to pull start (push start/roll start) it made a not normal sound  and wouldnt stay running.
      If my bottom end is blow why would it still turn over fine,
      Are my valves siezed or not working properly 
      or is my timing off causeing valves to not open in correct order with fire 
      PLEASE HELP all help is appreciated 
    • By Hunter Aldridge
      Some times I get spark some times not can ride then it just dies and wont get spark it has new cdi box and stator but I don't know if it has the pickup coil I'm at a loss
    • By William Sims
      I have a 400 4by4 ,2005 green model,
      wounding how many different CDI boxes will work on it
       
    • By jerry houston
      Eiger 400 Suzuki runs fine Cook-Out joke face off the handlebars put it back on and will not start now will crank no no spark
    • By colin james
      View File 2012-2014 Polaris Sportsman 400 HD Service Manual
      This the factory service manual for the 2012- 2014 sportsman 400 hd service manual 
      Submitter colin james Submitted 02/08/2019 Category Polaris ATV  
  • Similar Topics

    • By Sha35297
      Hello, got this bike in to replace the jug and piston. Made the swap, crank looks good, no play in connecting rod. Put it all back together and then heard a rubbing noise in the rear crank case. Ordered a new timing chain and tensioner. Installed them and put it all back together. Fired it up and ran great on the work bench. Took it down and went for a ride and noticed the higher the rpms, the noisier it got. There was a tapping noise on the exhaust side of the valve cover. Removed valve cover. Checked valve clearances, all good. Checked the valve springs, the were a good bit out of tolerance. Installed brand new springs. Same noise. Decided to replace the whole cylinder head with one from a known good bike. Still the same noise. Decided to replace the camshaft with one from a known good bike. Still makes the noise. Replaced lift caps. No change. I’m at a loss on what could be causing this noise. It’s very loud and not normal by any means. Any suggestions would be appreciated. Video doesn’t really pick up the noise good, but it’s there. 
       
      Thanks
      IMG_2225.MOV
    • By AKMichael
      Hello All,
      I have a 1999 Yamaha Big Bear 350 4x4 trying to get fixed up so my grandson can go out in the woods with me.
      We have owned it over 10 years.  It got harder to start, until it finally would not.  Replaced the carb.  Right afterwards, it started and ran nicely, but after turning it off, would not restart.  Tonight I used starting fluid and ran, then died.  Adjusted the idle up a little, used more starting fluid and ran great.  It idled about 15 minutes.  Turned it off, and restarted.  Ran it around the yard about 5 minutes.  Turned it off, and would not restart.
      Any ideas or suggestions would be greatly appreciated!
      Thank you. 
    • By Brennon Heflin
      So I bought a 2000 quad runner 250. I'm having some issues an wondering what it could be I replaced the pet cock valve an the fuel filter an pump inside tank I also put a voltage regulator on it. The problem I'm having is that when u give it half or more throttle it bogs down an loses power what could it be the bike is almost like new an cant figure it out any help would be great
    • By mike91
      I’m just wondering what year bike i got? it seems the vin has been rubbed off i got it from a auction here in Australia engine starts but seems has a dirty carb wont idle well
      and also has a problem I put it in gear and makes a grinding noise but does not move it the neutral light goes out but then when I change gear it grinds more in the higher gears as well I’m guessing the differential is stuffed so wanting to buy new part for it will start the pull down next week

      this is the first bike I have worked on used to dealing with cars




    • By hutchir3
      Hello Folks....new to the forum.  I have two Warriors (87 and 92), and an 89 Big Bear.  Looking for some help with engine issues on the warrior, and my 89 Big bear backfired and died. Got spark, got gas, seems to have compression, (but haven't tested it yet...next). She rolls over good, maybe too good...seems soft. Have spark and enough compression to blow gas mist out the plug hole when cranking. Suggestions, Been running great since we got it.

  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...