Quantcast
Jump to content

Recommended Posts

Posted

I was out riding and it quit on me. I was going sslow when it happened with low rpms. engine feels like it has the same compression.

I ahev not checked anything yet

what would be the first few things to check on in order of likely hood

Posted

I checked to see if it was sparking. it did but it seemed weak. but my starter does not work well. I usually kick start it. I could not get any spark kick starting.

but it did show a spark with the weak starter. Not as bright as my chain saw though.

is this one of those things where the ignition system is either working or it isnt or could it be working in a weak way

Posted
i think it will work in a weak way ... i would check regulator,

but i think stator might be toast, or just the pick up coil ...

The plug is black and pretty sooty looking.

could that be enough to cause a weak spark?

Posted
if it was black, it didnt burn or too rich. so yes makes sense being weak ...

then I guess its kind of a chicken egg thing I have to figure out. did the plug get sooty because of a rich mixture and then it fouled

or was the spark weak so the fuel didnt burn so the plug turned black

Posted
does your neutral light come on ok ... was just thinking of other possibilities with the spark ...

the neutral light is always on. I didnt worry about it because it wasnt an issue until maybe now.

I am looking into wether the battery is completely dead or not. I know on my mowers, if the battery doesnt charge or it goes bad the mower will stall out. even if you jump it and the battery doesnt have enough of a charge they will stall.

wasnt sure if this atc could be similar.

Posted (edited)

my buddys big red had a bad battery but would kick start and run fine. thinking you could do a test on the stator and pick up coil, but not sure how easy it is with the cdi ...

i would pull all the connections and clean and grease them ... could be that simple too ...

Edited by oxidized_black
Posted

I charged a better battery. on the plus side I found out my starter isnt bad. Even though the old batter would get the head light to work it didnt produce enough amps to turn over the starter.

on the negative side , I have gone from weak spark to no spark.

so now I am going to test components and clean contacts

Posted

I have noticed something odd. I tried turning over the motor with an auxiliary batter by connecting the positive to the starter and the neg to a spot on the motor with the use of short jumper cables and I could not get the starter to turn.

when I hooked up the same battery to the old battery terminals on the atc then the starter would turn that way.

shouldnt the starter spin a good battery is hooked up directly to it with the engine cooling fin as a ground?

this may tell me I am not grounding the spark plug properly when checking to coil

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By RGS
      1989 Moto 4 YFM350ERW intermittent spark.
      Quad has set for about 7 years and was running when parked.  When I replaced the battery and attempted to start it had no spark. 
       
      What I have done.  Followed troubleshooting in the manual. 
      1.       Coil failed the resistance check so I replaced it.  Still no spark.
      2.       I performed resistance checks on the stator and they all pass.
      3.       Found a bad rear brake stop switch and unplugged it and connected the wires in order to disable.  Now I have intermittent spark.  I believe that the issue is with either the stator or CDI and not sure which.
      1989 seems to be a transition year for electrical.  I can get new aftermarket CDI units for 87-88 and 90-94.  I cannot get ones for a 89.  I can get new stators for 87-89 and 90-95.  Looking at the schematics the wiring on my moto is closer to the 90 ones on the ATV side of the CDI and closer to the 87-88 on the stator side of the CDI.  Looking at part supply sources the stator housing is the same part # for all the years and looking at some of the stators on Amazon that have the dimensions on them both of the stators are the same size.
      What I am thinking of doing is to replace the stator and CDI with a 90-95 one as these parts are all readily available.   Does anyone know if this has been tried before and if there are any issues with doing this.  
       As a side note I also have a 1993 Moto 4 YFM350ER that has been sitting longer but it is located about 400 miles from me at this time.  By doing this change in addition to being able to get parts I will also have 2 ATV’s that are the same electrically. 
    • By Thumpinhard25
      First thanks for any help guys, new to the forums and it's gotten me this far. I bought a 2001 bear tracker 250 for my family to get around the dirt bikes races. It wasn't running right and had a high idle. Previous owner thought it was a carb problem, so he ordered a new Zoom carb and new intake boot, but it still had the same high idle. ( I believe he had the throttle cable adjusted wrong, because it idled fine when I put it back together) So I tore down and cleaned the stock carb, and it started up and idled fine, but needed to have the choke 1/2 out to run.  I swapped to the new zoom carb and had the same issue. Choke half out bike ran ok. I played with the needle and the pilot screw with no change. ( bike did seem to be running rich though, but didn't get better when I tightened pilot screw or raised meddle) I Took it to the races and once I started bouncing around in the cattle fields the quad started cutting out real bad. It would barely run.  Sometimes it would run with choke off, sometimes choke 1/2, sometime choke full. I cleaned carb again, checked float level, and boots, no change still wouldn't run. Then suddenly it started running ok again.  This makes me believe it's an electrical issue rather then carb. I know there's no air leak, it's been checked, both carbs are clean( I've swapped them out a couple times, it starts up immediately and usually idles fine. But then bogs down/ or stutters under throttle. I saw the post on the guy who disconnected his rectifier and reconnected and suddenly it started working again, which lead me to believe it may be electrical and not carb.  So any advice on what I should check? Any way to test the CDI or rectifier?  Once again, I appreciate your help.  
    • By Kaz
      Troubleshooting a no spark issue, was running OK, maybe a little rich, turned it off, now no spark. I've checked/ohmed out the main key switch, the start/stop switch, neutral switch, brake switch - all good. It will crank the starter, but no spark with the starter or when I try the pull start. I've checked all fuses and diodes. Swapped battery. New plug. New coil. Swapped in a used CDI - no help. Traced, removed, cleaned, reattached all grounds. Removed things like my winch from the circuits to be sure a bad relay or something was dragging it down. When testing voltages, the orange wire going from the CDI to the ignition coil shows no/very low voltage-shouldn't it have 12V on it? Sometimes I get a very weak, intermittent glow on my spark tester, but not enough to fire the plug. I've checked continuity on just about all wires in the harness. Checked/cleaned/lubed w dielectric grease- all connections, redid a few that looked old/dirty. I've checked the stator resistances, all good, but have a stator and rectifier ordered anyway, will arrive Sunday. I verified that the rectifier has a voltage output back to charge the battery while cranking - 10.5-11V, low, but expected while starter is engaged. What else can I check as part of troubleshooting? I have a Haines service manual, but the 1999 350 4x4 seems to be an odd model, there isn't an exact electrical diagram for it, but found one for another year that has all the same number of wires and same color wires, so I've referenced that. Any hints, tips or advice would be appreciated! Thanks!
    • By Kawasakibayounospark
      any one know much about how this system works. Replaced voltage regulator cid box coil pickup coil have power to cid box none out to coil any thoughts. This is cid box number three 
    • By carkivey3
      i just picked this up. was told ran fine but overheating issues led to replacing head gasket and head. has not ran since. he is not a mechanic but helped someone else who he could not get back to finish job, got aggravated and put up for sale. i was thinking timing issues. i have 110-120psi on all 3 cylinders so i think valves are correct. dont know about distributor yet. however i have no spark. i have no power going to ignition coil. tried to follow white wire but gets lost in wire harness. does anyone have a wiring diagram? can anyone tell me what conditions have to be met before starting. motor turns over so i would think all safeties are met but you never know.
×
×
  • Create New...