Quantcast
Jump to content

2013 Honda Rancher 420 ES - Wont Start

jimbog526

By jimbog526
in Honda ATV Forum

 Share

Recommended Posts

jimbog526 Rookie

jimbog526

Posted
Posted

I have a 2013 Honda Rancher ES that wont start. Last night after running the atv for 10 minutes I parked it for 2 minutes. When I came back to start it up the atv would not run. It was turning over. All electronics are working properly. The battery is strong. I sprayed a little bit of carb cleaner in the intake with filter off and the atv started for a second. I changed the spark plug and it still wouldn't run. Whats the next step to check before giving up and taking it to the dealership?

oxidized_black Grand Master

oxidized_black

Posted
Posted

i would pull the spark plug and make sure you have spark, i think you do because the carb spray almost started it, then i would pull the fuel supply hose and make sure you are getting gas. check too that the kill switch isnt on and the bike is in neutral ...

jimbog526 Rookie

jimbog526

Posted
  • Author
Posted

the kill switch is not on and the bike is in nuetral. Ill make sure im getting fuel...ill update this tomorrow night.

This is very wierd. I drove a few time last night and it ran great. then all of the sudden without notice it wouldn't start. THANK GOODNESS I was in the garage and not in the woods!!! Thanks for your replies.

jimbog526 Rookie

jimbog526

Posted
  • Author
Posted

Update:

I checked all fuses and all looked good. I powered up the atv and didn't hear the fuel pump cycle. I checked warranty and its good until the end of next month. So Im taking it to the Honda Dealership tomorrow for repairs. I will update this forum as soon as I find out what the issues are with the Honda.

oxidized_black- Thanks again for all of you help!

jimbog526 Rookie

jimbog526

Posted
  • Author
Posted

The dealership couldn't find an issue. They said after they went through everything and cleaned the terminals on the fuel pump that the four wheeler started right up. So Im guessing the issue was a bad connection. Thanks for all of your help.

  • 6 years later...
Ajmboy Grand Master

Ajmboy

Posted
Posted
On 4/11/2020 at 6:27 PM, Randy Hood said:

My 2013 honda rancher wont start. The magnetic cylinoid that connects behind battery just clicks.  I have replaced it with a new one new starter new battery. It still just clicks.  Please help

Can you jump the starter solenoid?

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Popular Now

  • Similar Forum Topics

    • realpilot
      1999 Ranger 6x6 no start
      By realpilot
      I am unable to find a wiring diagram for this UTV.  When I turn the switch to on, the contractor does not engage.  The Brake pressure switch and the parking brake switches work correctly. What else should I be looking for?  All of the diagrams I have found are for newer models and the wire color coding is different.
       
      Thanks
    • Cj Winds
      2009 Honda Rancher TRX420FA with shifting problems
      By Cj Winds
      I have a 2009 Honda Rancher TRX420FA with shifting problems.
      Usually it shifts ok when cold but after couple minutes it will stop shifting with no codes.
      The 1st shift clutch oil pressure when in first gear is 74psi. The 2nd shift clutch oil pressure when in second gear is 74psi.
      The 1st shift clutch oil pressure when in neutral is zero. The problem is when the tranny is in neutral the 2nd shift clutch pressure starts around 10-15psi and builds to 20psi. Is this normal?
    • OldATVowner
      99 Bear tracker no neutral or reverse light or start button
      By OldATVowner
      Just getting into this issue really. Been replacing solenoids but now I'd like to track down the problem. This time I'm not getting neutral/reverse lights or start button. Was on a creek ride when it started doing this recently. It cranks by arcing the solenoid and gives me no light or start button but if I crank with the pull cord....the neutral light and the button work. Turn it off and try to crank with the key and nothing. I'm looking into the safety switch issue tomorrow and re charging the battery. Just figured this was odd enough of a problem that you guys might be familiar. Thanks
    • Mikey509
      2000 honda recon battery charging
      By Mikey509
      Hey guys, so I've been messing with my quad, and between all the starts, the battery is dead. Is there a certain way to charge these? Can I just throw a trickle charger on it and call it a day? can i also jump it like a normal car with a battery pack or is that to much voltage 
    • Mikey509
      2000 honda recon fourtrax 250
      By Mikey509
      Hey guys i recently got a old recon 250 up and going and the prev owners had the carb screws all messed up. i was wondering if anyone can give me the basic run downs on if i turn both screws all the way "tightened" how many turns out will the quad run okay so i can then dial it in. the prev owner had the screws messed up so bad it woudnt idle. i got it to idle but idles rough. its super lean any guidence is appreciated 

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...