Quantcast
Jump to content

Recommended Posts

Posted

I don't know what to make of this. I have an Arctic Cat 2005 automatic 500 with PVC home-made snorkels that came with the ATV from the previous owner. I finally decided to remove them as I needed the room for the front cargo rack. The flexible rubber tubes where the extensions fit into are the same diameter as the extensions, and end just under the front "hood" cover. Not too different, other then length of the air intakes. Yet, the machine acts like it's not getting enough air. In other words, it lugs down under acceleration or going up hills. Throttle response is drastically reduced, unless you're moving on a level terrain, but, still noticebly less power. With the snorkels removed, the machine is totally responsive, lots of power, and no lugging up hills, actually can accelerate.

What's the deal here? Does the carb need to be adjusted? With the snorkels off, am I getting too much air or not enough? I would think not enough air. Can anyone help with this?

Larry

Posted (edited)

the carb was probably jetted to compensate the extra air ... if you replace the jets to stock, you will probably be alot happier and not have a sluggish bike ... i bet if you take the airbox lid off, it might be a little better ...

Edited by oxidized_black
Posted

I need the rack space too, and the streams here in Panama are not very deep, so I didn't need the snorkels. I did find a half dozen jets in the package left with me by the former owner, so I suspect he did change the jets. I checked into trying to put the original air filter back in, but whoa, you have to take the whole rack, bumper, winch, and plastic off to do that. So no way.

Now...I figured out the perfect solution. I re-routed the snorkels, under the plastic shroud, next to the headlights. Perfect. They're not in the way, still high enough should I encounter 3 feet of water (not going to happen), and it runs superbly. Even can accelerate going up steep hills. I feel like it can leap tall buildings too.

Thanks for your input, I learned something too about jets.

Now, I have something else...I noticed it a couple of days ago. There is an engine noise I didn't hear before. While the engine is running there is a "ting, ting, ting" sound, almost like a lifter or tappet, but higher pitched. Anyone have any idea?

Edit/Delete Message

Posted

I found the source of the "ting, ting, ting". It's the fuel pump. It just started doing that after I blew "lung pressure" air through the 3 lines connected to the fuel pump. However, I did not blow air into the fuel pump. What's up with that? Is this pump dying? I'd hate to be half way up a hill when it did.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Popular Now

  • Similar Forum Topics

    • By tepin
      Здравствуйте, нужна помощь по ремонту багги Arctic Cat 700 EFI, пропала искра, датчик коленвала импульс есть, Самодиагностика показывает две ошибки AC99,AC96. все провода проверил на целостность, все датчики блоком определяются, не включается топливный насос. Провода от ECU до реле насоса и от реле до насоса исправны. Поставил подменный ECU, ничего не изменилось.   

    • By Mikey509
      Hi guys, I was given a 2000 Honda Recon fourtrax 250 (I think that's the full name lol). The previous owner had it sitting for a while before I got it. It sat for another few years in my ownership. I got it up and going on its first test drive today!! I was wondering where everyone buys their parts from?  Coming from the car community, we have sites like RockAuto and many more. Anything like that for quads? Also would like to be pointed in a direction, if possible, for plastics. I am missing a few and would like to have it complete. I appreciate any input!
    • By Shorty51
      Good morning, I am new to the forum. I'm 75 years old and love getting ATVs back to usable condition. I particularly like the 2006-2009 Arctic Cat 250 Utility. I currently own 6. The 2006 I am working on only has reverse and low gear. The "drive shaft" in the transmission is completely stripped where the high gear would mesh. Has anyone on here replaced the shaft. I'm told I have to split the case. I was hoping that someone on here could let me know how hard it will be. I already have it stripped down to where the shaft coming in from the clutch side is the only thing left. I was hoping I could just remove the driven clutch and drive it out from there. Directions say different. Any help would be greatly appreciated.
    • By rjsummer
      I just bought a 1984 Suzuki LT185 ATV and am looking for the OWNER’S manual. ( not a service manual) 
      I contacted Suzuki Canada but they have no paper or digital copies in their archives. 
      Does anyone possibly have a digital copy they’d be willing to share? 
    • By TomJulio
      Looking for two stock front wheels for 92 TRX300 2WD.   I think they are 6 x11" size.     
×
×
  • Create New...