Quantcast
Jump to content

1997 Kawasaki Bayou 300 4x4 - Service Manual

rattlecanrobby

By rattlecanrobby
in Kawasaki ATV Forum

 Share

Recommended Posts

rattlecanrobby Rookie

rattlecanrobby

Posted
Posted

Hey guy and gals

I'm a new-be here an just need a lot of help

So please forgive me if I'm doing this wrong!

First off My name is Rob and thanks for having me here you'll.

I just acquired a 1997 farm hand bayou 300 4x4 that is in need of a lot of TLC I traded the fella even up for and old Yamaha street bike I had about $850 into that ran good and did not leak or burn oil but still needed many minor things like brake worked seat and so on

So about the Bayou-it runs starts right up and all but is missing some things like the front and rear racks clutch lever and small plastic cover in front of handle bars

My issue is that the fella said he put new piston & rings in it about a week ago and checked out the clutches like I said it runs and I know I should have taken more time to check everything out so when I got it home I found out there was no air breather and I can't see how one would have even fit on there the way the carb is so close to the inner frame rail under the seat on it and it started leaking oil pretty bad from the clutch cover (it was clean oil though light in color)

The quad is not bad lookin and I can weld up some racks for it but I really need a service manual for this old work horse!!!!! I have no issue following directions other than sometimes giving my own creative touches LOL

ANY HELP WOULD BE SO MUCH APPRECIATED

THANK YOU AND HAVE A BLESSED DAY

ROB

  • 4 years later...
Timother Limbrick Newbie

Timother Limbrick

Posted
Posted

I just bought a 1999 Kawasaki Bayou and it won't fire but one time then stop. I'm needing to see the wiring diagram to try and troubleshoot this problem. My hope is that this manual will have enough information to work with. I'll post again once I have reviewed it. Thank you so much for posting this file.The vehicle is old and finding good info other than the owner's manual has been difficult. God bless you!

  • 2 weeks later...
  • 2 months later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • Atomusthenes
      88 Honda four trax 300 4x4
      By Atomusthenes
      I would appreciate being pointing in the correct direction for a wiring diagram and or schematics of the 88 Honda FourTrax 300 4x4 if anybody has any knowledge of how to test the ignition system stator and CDI I don't know if the voltage regulator probably and also the FCU I put a new ignition in it it is a cheap aftermarket one doesn't have the correct plugs but has the correct wiring scheme I get power  the neutral light comes on and the oil light stays on it turns over but I have no spark
    • kawasig
      I just bought a rare beast!
      By kawasig
      Hello All
      I'm kinda new to ATVs. I just bought a 1987 Suzuki quad runner 230 Dual Range. I'm having a problem finding info on it. It's very clean, only 2.800 miles. The front wheels are only 30 in.center to center. I was thinking about adding wheel spacers to give it more stability. I realize the added stress on ball joints and bearings. I'm wondering if there are any other concerns? Any input is greatly appreciated!
    • Memphis
      Quadzilla 300
      By Memphis
      Not sure if in right place but here goes
      My 300 is lacking power only reaching 30mph and struggling uphill everything else seems ok other that this problem cleaned all fuel new filter pan and all new fuel pump and spark plug full oil change is there anything I am missing
      ps It is auto and does noy seem to want to get in another gear 5200 rpm at 30mph
       
      Regards
    • Tim Keiper
      2 problems with 2000 Timberwolf 4x4
      By Tim Keiper
      1st problem, Does anyone know where I can find a stock carb for my Timberwolf, I have tried two different aftermarket carbs and they both suck. The machine runs great until it gets good and warm, then it keeps stalling unless I feather the throttle. it will even stall while I'm trying to go from 1st to reverse or vise versa. I took it to a buddy of mine who is a bike mechanic for years, and he told me try to find a factory carb. When I look online from dealers it says "NOT AVAILABLE" anyone have any suggestions ?
       
      2nd, The small tab on the rear axle for towing is to short for even pulling my small yard trailer, I can't even turn a little bit and hit hits. I tried making an extension which worked great as far as length, but it bends the tab and then the extension drags the ground. I have an idea of what to do to fix it, but wanted to see if anyone else has had this problem and see how you solved it.
    • Kaz
      1999 Yamaha Big Bear 350 4x4 no spark
      By Kaz
      Troubleshooting a no spark issue, was running OK, maybe a little rich, turned it off, now no spark. I've checked/ohmed out the main key switch, the start/stop switch, neutral switch, brake switch - all good. It will crank the starter, but no spark with the starter or when I try the pull start. I've checked all fuses and diodes. Swapped battery. New plug. New coil. Swapped in a used CDI - no help. Traced, removed, cleaned, reattached all grounds. Removed things like my winch from the circuits to be sure a bad relay or something was dragging it down. When testing voltages, the orange wire going from the CDI to the ignition coil shows no/very low voltage-shouldn't it have 12V on it? Sometimes I get a very weak, intermittent glow on my spark tester, but not enough to fire the plug. I've checked continuity on just about all wires in the harness. Checked/cleaned/lubed w dielectric grease- all connections, redid a few that looked old/dirty. I've checked the stator resistances, all good, but have a stator and rectifier ordered anyway, will arrive Sunday. I verified that the rectifier has a voltage output back to charge the battery while cranking - 10.5-11V, low, but expected while starter is engaged. What else can I check as part of troubleshooting? I have a Haines service manual, but the 1999 350 4x4 seems to be an odd model, there isn't an exact electrical diagram for it, but found one for another year that has all the same number of wires and same color wires, so I've referenced that. Any hints, tips or advice would be appreciated! Thanks!

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...