Quantcast
Jump to content


2003 Arctic Cat 500 Auto TIS - Carb Probs


Recommended Posts

Hello all, hope someone can help me out. Just did an overhaul on this 500 TIS and I still have a carb issue. This is one of those carbs with two additional rubber diaphs in it. When ridding in H it seems to be starving for gas and quits all the time. When ridding in L it works better until you really need some power then same thing, starving for gas. I have all the settings per the manual. Can anyone give me a clue as to where I may need to make an adjustment?

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By HSTAR
      Hey I have a 1997 big bear 350 4x4
      I replaced the shifter shaft and the shift arm linkage and the rod when I installed them all I was unaware that you had to line the dot on the shifter shaft with the gap on the linkage arm gap put it all back  together and rode it I can't get it to shift in the right gears  I can move the shift cam by hand and goes in different gears but with the shifter shaft in it riding I can't put it in R or N 
      Anyone know how to line up the shifter shaft and the shift cam s
       
    • By Clydaho
      2022 Sector 550, 414 miles on it and the gas gauge reads empty.  I topped off the gas and it didn't change.
      There is no fuse that I could find.  No access at the gauge cluster.
      Wiring on the top of the tank looks good, properly connected.
      Could the sending unit in the tank be stuck or broken?
      Has anybody removed the tank lid?  Any tricks?  
      Any other ideas?
      Thanks for any help,
      Clyde
    • By ethie
      Hi All
      I have a 2012 Coleman 500 Outfitter that keeps fouling out the plug within 10-15 minutes 
      not sure where to start
    • By rgeiser
      View File 2003 Polaris Ranger 400-500 service manual
      2003 Polaris Ranger 400-500 service manual
      Submitter rgeiser Submitted 04/18/2024 Category Polaris UTV  
    • By ResQ91
      Hi Guys!

      New member and could really use your advice. I would have to believe this has been an issue for others but a search here came up with nothing......? (Probably me not doing search correctly)
       
      I have an 87 Big Bear 350 YFM350FWT
      The OEM Mikuni BTM carb is shot and would rather replace than rebuild.
      It is no longer made and I have had good luck with NICHE carbs so I ordered a #K-CRB-0006 This was what they said was replacement when ordered. This Carb only uses 1 Throttle cable. The Slide is linked so it uses one. (OEM had 2nd cable coming through top to move slide)
       
      Problem is when I ordered a replacement Cable from NICHE (#C-CBL-0061) the Cable wire is a little short, not allowing Throttle to return all the way down to Idle position. I called NICHE and they are at a loss. Haven't gotten back to me after 2+ weeks.
       
      What would you recommend other than a carb rebuild?
      Can I just use 1 of the OEM cables (It is the right length) and snip/disconnect the other that went to top of Carb for Slide?
      Or ??
       
      Thanks in advance for any advice you have!!
       
      Dave
×
×
  • Create New...