Quantcast
Jump to content


1995 Honda Fourtrax 300 issues


tmiles

Recommended Posts

I just bought this 300 2wd and I don't know much about working on them. I have the service manual and the owners manual from online downloads but...

Hoping I could get some help please:

1) Pretty sure I am just going to have to but a new carb but see what you all have to say. When it is cold I have to shoot some starter fluid on the air cleaner. Choke cable seems to be sticking and not working. Once the quad is warmed up I don't need any more starting fluid it will start on its own but the big issue is it will not idle. I have to keep giving it just a little bit of throttle. I took the carb off but could not get the choke cable out the carb and someone has already stripped the 4 heads on the screws holding the bowl on. Cheapest place to buy a carb? Any other ideas?

2) Shifts really hard through all gears. Pulling the shifter up with my foot is hard but when it shifts it wants to slam into gear and actually jerk the quad. If your going with a little bit of speed it wants to pull the front tires up a little. Any ideas?

3) Pulls to the right terrible. Tire pressure is good. Nothing looks physically bent, arms, t-rods nothing. If I adjust the t-rods should I turn the right side in toward the center of the quad to get it to pull more to the left to even it out?

Thank you for your help.

Tim

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By exalrod
      Hello All !
      I am looking for a service manual and wiring diagram for a 2005 50cc Polaris Predator 4 wheeler.
      Could anyone help with this?
    • By exalrod
      Hello All !
      I am looking for a service manual and wiring diagram for a 2005 50cc Polaris Predator 4 wheeler.
      Could anyone help with this?
    • By pitts
      Just joined so I can download a manual and In the process of making my 10 posts.
    • By Brantley11
      Hey everybody,
       
      My proficiency is with Hondas and Yamahas make me see RED!
       
      This bike is my brother in law's, it has 1199 miles on it and went from running great to dead with no start. Every once and a while it will start and sputter for 2 seconds. It is extremely sporadic when it fires but never runs for longer than 3 seconds. 
       
      Here is where we sit:
      Brand New Fully Charged battery
      Carb was cleaned with air hose and carb cleaner then into the ultrasonic cleaner with Aircraft aluminum cleaner
      New Shindy Carb kit (made in Japan version)
      Cleaned out petcock and gas tank
      New 93 Non Ethanol Gas
      New Spark Plug
       
      It gets a spark through the spark test light every time
      Bluish white spark
      When holding the spark plug 1/4" - 3/8" away from head it will jump and spark to the head
      Good Compression
       
      Here are the readings:
       
      Pickup Coil 519 Ohms (range 459-561)
      Charging Coil 266 Ohms (range 270-330)
      Lighting Coil 0.700 (range 0.702-0.858)
      Spark plug Cap 10.58 Ohms (10kohms
      Ignition Coil Primary Coil 0.5 ohms (range 0.18-0.28 ohms)
      Ignition Coil Secondary Coil 8.20 kOhms (range 6.32-9.48 kOhms)
       
      Would y'all think stator and pick up coil, rectifier or CDI are the culprit?
       
    • By bob2007
      Hy there great to be able to communicate with people having knowledge I have a continuous problem with a leaking carburetor and I just saw a small rubber hose detached from the bottom of the carburetor and i cannot find were it should be attached and how the two side should be affixed to the carburetor any suggestions as i cannot find a description plan on it thank you Bob
×
×
  • Create New...