Quantcast
Jump to content


Fuel Gauge Replacement 1997 Yamaha Kodiak 400

coderunner

By coderunner
in Yamaha ATV Forum

 Share

Recommended Posts

coderunner Rookie

coderunner

Posted
Posted

I have a 97 Kodiak 400 4x4 and the fuel gauge in the tank was damaged when I got it. I would like to replace it and Yamaha has given me a price of $50 for the parts. I have a Clymer manual but it does not give the remove and replace instructions for the fuel gauge only the tank. Any wizard out there that can give me the info or point me in the right direction?

Thanks in advance

Code

Link to comment
Share on other sites
  • 1 month later...
  • 2 years later...
Fireball Rookie

Fireball

Posted
Posted

I have a 2000 big Bear 400. probably the same part. The guage on mine works, the clear plastic cover is not clear, and broke so gas splashes out. It looks like the silver cap retaining it has little detent clips cut into the side that can be gently un-hooked with a dental pick or similar tool to remove the cover, but is pointless without a replacement part. Anyone have a PN for that? There may be an o-ring in there as well.

Link to comment
Share on other sites
Fireball Rookie

Fireball

Posted
Posted

OK, I already found the answer to my own question. The guage unit sells for $30, and bezel for $6 from PowerSportsPro.com. Since my guage functions I am ging to remove the decomposed (due to ethanol?) clear part and epoxy on an old watch crystal. If it doesn't work it cost nothing to try.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • HSTAR
      1997 Yamaha big bear 350 Shift shaft issue
      By HSTAR
      Hey I have a 1997 big bear 350 4x4
      I replaced the shifter shaft and the shift arm linkage and the rod when I installed them all I was unaware that you had to line the dot on the shifter shaft with the gap on the linkage arm gap put it all back  together and rode it I can't get it to shift in the right gears  I can move the shift cam by hand and goes in different gears but with the shifter shaft in it riding I can't put it in R or N 
      Anyone know how to line up the shifter shaft and the shift cam s
       
    • semicolon
      TRX350D fuel pump problem
      By semicolon
      Hi, I am having issues with my TRX350D fuel pump.  It suddenly stopped running so I have replaced all the fuses and cleaned all the terminals.  I have fitted a new pump, fuel cut-off relay and rectifier.  Still nothing!!  The pump runs when attached to a battery.  The engine will start on the choke and the filter fills with fuel but it will  not rev and dies when the choke is closed. I have power to the relay but nothing at the pump black/white wire when cranking the engine.  Any ideas where to go from here would be very much appreciated!!
       
    • John Sinclair
      1992 yamaha big bear 350 carburator issues
      By John Sinclair
      I WANTED TO UPGRADE THE CARBURATOR ON MY 1992 BIG BEAR 350, SO I ORDERED A NEW CARB FROM EBAY.  ACCORDING TO THE WRITE-UP IT WAS A GOOD FIT FOR BIG BEARS FROM 1988 TO 1996.  WHEN I REMOVED MY ORIGINAL CARB I NOTICED THAT IT WAS DIFFERENT FROM THE NEW CARB MY CARB HAD TWO THROTTLE  CABLES THE NEW CARB ONLY HAD ONE CABLE.  HOW CAN I MAKE THIS CARB WORK ON MY TWO CABLE THROTTLE?  
    • Clydaho
      2022 Hisun Sector 550 Gas gauge stopped working
      By Clydaho
      2022 Sector 550, 414 miles on it and the gas gauge reads empty.  I topped off the gas and it didn't change.
      There is no fuse that I could find.  No access at the gauge cluster.
      Wiring on the top of the tank looks good, properly connected.
      Could the sending unit in the tank be stuck or broken?
      Has anybody removed the tank lid?  Any tricks?  
      Any other ideas?
      Thanks for any help,
      Clyde
    • McG75
      1996 Yamaha Timberwolf 4x4 Rear End Width
      By McG75
      1996 4x4 Timberwolf rearend width. Can someone with some knowledge of these machines answer this question for me please. Are all 4x4 timberwolves this narrow in the rearend? These tires are so close the right one actually rubs the muffler.  Thinking about seeing if there are any spacers out there for it. I need at least an inch more clearance. 
      .
       
       

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...