Quantcast
Jump to content


2001 Yamaha Warrior 350 need help


lipo39

Recommended Posts

Sounds like the solenoid is sticking, it could either be the solenoid itself, the starter relay or the start button. You can test the solenoid by disconnecting power wire from the starter and hitting the start button, when you let go, check for voltage on the low current solenoid feed wire that feeds the start signal to the solenoid. If you get no voltage on that pole, test for voltage at the end of the starter wire where it would normally be connected to the starter. If the wire is still hot, then the solenoid is bad. If there is still power at the solenoid feed wire after you let the start button go, then it is either the relay or the start button. Next you need to find the relay if there is one, test that, and lastly test the wires coming out of the start button, see if they have continuity still after you let the button off.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By HSTAR
      Hey I have a 1997 big bear 350 4x4
      I replaced the shifter shaft and the shift arm linkage and the rod when I installed them all I was unaware that you had to line the dot on the shifter shaft with the gap on the linkage arm gap put it all back  together and rode it I can't get it to shift in the right gears  I can move the shift cam by hand and goes in different gears but with the shifter shaft in it riding I can't put it in R or N 
      Anyone know how to line up the shifter shaft and the shift cam s
       
    • By John Sinclair
      I WANTED TO UPGRADE THE CARBURATOR ON MY 1992 BIG BEAR 350, SO I ORDERED A NEW CARB FROM EBAY.  ACCORDING TO THE WRITE-UP IT WAS A GOOD FIT FOR BIG BEARS FROM 1988 TO 1996.  WHEN I REMOVED MY ORIGINAL CARB I NOTICED THAT IT WAS DIFFERENT FROM THE NEW CARB MY CARB HAD TWO THROTTLE  CABLES THE NEW CARB ONLY HAD ONE CABLE.  HOW CAN I MAKE THIS CARB WORK ON MY TWO CABLE THROTTLE?  
    • By McG75
      Hello I’m new here and was wondering is anyone knew of good replacement part numbers for front struts and rear shocks for this atv? I think I’ve found a new rear shock, that looks like the original but there is no dimensions or anything and was wondering if there are any afterMarket new front struts available. I know it’s a long shot but any help would be appreciated. 
    • By McG75
      1996 4x4 Timberwolf rearend width. Can someone with some knowledge of these machines answer this question for me please. Are all 4x4 timberwolves this narrow in the rearend? These tires are so close the right one actually rubs the muffler.  Thinking about seeing if there are any spacers out there for it. I need at least an inch more clearance. 
      .
       
       
    • By ResQ91
      Hi Guys!

      New member and could really use your advice. I would have to believe this has been an issue for others but a search here came up with nothing......? (Probably me not doing search correctly)
       
      I have an 87 Big Bear 350 YFM350FWT
      The OEM Mikuni BTM carb is shot and would rather replace than rebuild.
      It is no longer made and I have had good luck with NICHE carbs so I ordered a #K-CRB-0006 This was what they said was replacement when ordered. This Carb only uses 1 Throttle cable. The Slide is linked so it uses one. (OEM had 2nd cable coming through top to move slide)
       
      Problem is when I ordered a replacement Cable from NICHE (#C-CBL-0061) the Cable wire is a little short, not allowing Throttle to return all the way down to Idle position. I called NICHE and they are at a loss. Haven't gotten back to me after 2+ weeks.
       
      What would you recommend other than a carb rebuild?
      Can I just use 1 of the OEM cables (It is the right length) and snip/disconnect the other that went to top of Carb for Slide?
      Or ??
       
      Thanks in advance for any advice you have!!
       
      Dave
×
×
  • Create New...