Quantcast
Jump to content

85 polaris trailboss 250 firing trouble

jefafa123

By jefafa123
in Polaris ATV Forum

 Share

Recommended Posts

jefafa123 Newbie

jefafa123

Posted
Posted

so I seem to have some trouble getting my old 85 trail boss to put out a spark. when I first got it it fired just fine but had no compression. After I rebuilt the top end and tried to start it there was no spark so I got on the internet and ordered a used coil that came off of the same bike and it worked and ran good for about two weeks. When I really got the engine going good it would lose power and start to bog down but would quickly recover after a few seconds. Then one day it wouldn't starts and I found that it was not firing at all. Now I`ve put a brand new coil and there is still no spark. Everyone I know seems to think its the cdi box. However when I search on the internet everything points to the stator. Is there a way of testing either one?

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • RGS
      1989 Moto 4 YFM350ERW intermittent spark.
      By RGS
      1989 Moto 4 YFM350ERW intermittent spark.
      Quad has set for about 7 years and was running when parked.  When I replaced the battery and attempted to start it had no spark. 
       
      What I have done.  Followed troubleshooting in the manual. 
      1.       Coil failed the resistance check so I replaced it.  Still no spark.
      2.       I performed resistance checks on the stator and they all pass.
      3.       Found a bad rear brake stop switch and unplugged it and connected the wires in order to disable.  Now I have intermittent spark.  I believe that the issue is with either the stator or CDI and not sure which.
      1989 seems to be a transition year for electrical.  I can get new aftermarket CDI units for 87-88 and 90-94.  I cannot get ones for a 89.  I can get new stators for 87-89 and 90-95.  Looking at the schematics the wiring on my moto is closer to the 90 ones on the ATV side of the CDI and closer to the 87-88 on the stator side of the CDI.  Looking at part supply sources the stator housing is the same part # for all the years and looking at some of the stators on Amazon that have the dimensions on them both of the stators are the same size.
      What I am thinking of doing is to replace the stator and CDI with a 90-95 one as these parts are all readily available.   Does anyone know if this has been tried before and if there are any issues with doing this.  
       As a side note I also have a 1993 Moto 4 YFM350ER that has been sitting longer but it is located about 400 miles from me at this time.  By doing this change in addition to being able to get parts I will also have 2 ATV’s that are the same electrically. 
    • kawasig
      I just bought a rare beast!
      By kawasig
      Hello All
      I'm kinda new to ATVs. I just bought a 1987 Suzuki quad runner 230 Dual Range. I'm having a problem finding info on it. It's very clean, only 2.800 miles. The front wheels are only 30 in.center to center. I was thinking about adding wheel spacers to give it more stability. I realize the added stress on ball joints and bearings. I'm wondering if there are any other concerns? Any input is greatly appreciated!
    • Gwbarm
      Trail Tire Valve Replacement
      By Gwbarm
      Have you ever been on the trail and your tire valve goes bad. No way to break down the wheel and replace it. A lot of you probably know about this already i had heard of it but never used one. Just punch out the old one insert and tighten down the nut
       

       

       

       
      So far it has worked very well.
    • AnthonyT
      First time ATV buyer
      By AnthonyT
      In search of my first ATV? What are good older 4x4 models?
    • Frank Angerano
      My first trailer project.
      By Frank Angerano
      So I decided to pick up a small trailer if I could get one for the right price.  I found this one for a few hundred bucks on Craig’s list.  It is  a galvanized trailer which is exactly what I was looking for. The wood was shot and needed some minor repairs which I could care less about as long as the chassis was good. 
      I striped it down and put a new deck on. I had some vinyl realtree graphics that I had laying around so I added them to the fenders which I think worked out well. Very happy with this little guy.  
      I'm having the iron workers at my jobmake me up a few lightweight side rails that will have a 22 degree bend in them to accommodate the tires that slightly hang over the edge and will incorporate some tie down points as well. 








COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...