Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

wbholoch

Kazuma Coyote 90cc forward gear slipping

Recommended Posts

Hi all, I don't recall the year but I have two Kazuma Coyotes 90cc for my kids. One is fine the other one slips in forward gear to the point it won't run.

Before I tear into this anyone have an idea of gear box adjustment or what type this is? Direct drive, band type?

Any advice is appreciated since the kids are not very patient taking turns with one running go kart.

Thanks for the time.

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By PolarisRich
      I've never done this before but after reading a few thread I decided to check my valves for the first time and to my surprise it was much easier than I thought.
      My bike is a 2005 Sp 500 HO.
      I first pulled the seat and the right side panel off, and that's it! It wasn't too bad to get at.
      Next I pulled the spark plug out and removed both the head cover ( 8-8mm bolts)
      [ATTACH]1021[/ATTACH]
      then the side cam cover (5-8mm bolts).
      [ATTACH]1023[/ATTACH]
      Also remove the plug in the recoil cover (14mm bolt) to see the timming marks.
      [ATTACH]1022[/ATTACH]
      Next I turned the engine over with the pull cord untill it was at TDC of the compression stroke.
      The best was to tell that your at TDC of the compression stroke is to rotate the engine until the
      timing marks are parallel to rocker cover gasket surface.
      The cam sprocket locating pin will be facing upward directly in line with the crankshaft to camshaft center line.
      Now fine adjust by looking into the timing hole in the recoil cover and line up the upside down "T" on
      the flywheel into the center of the hole.
      [ATTACH]1023[/ATTACH]
      Now using a feeler gauge, slide the .006" (.15mm)blade between the top of the valve and the bottom of the adjuster and adjust accordingly
      [ATTACH]1024[/ATTACH]
      [ATTACH]1025[/ATTACH]
      To adjust, Loosen the locknut (10mm) and check clearance with a feeler guage. Clearance should be .006" (.15mm) for both, intake and exhaust valves. Turn the adjuster with a stubby flat blade screwdriver untill the proper clearance is achieved then tighten the locknut (5.8-7.2 ft. lbs) while holding the adjuster in place with the screwdriver. Re-check the clearance with the feeler guage one last time and re-assemble the covers (72 in.lbs) and plugs.
      The only thing that i noticed was that I had to clean and silicone the side cam cover other than that I found the whole process rather simple.
      I'd give it a 4 out of 10 on the skill level scale.
      I hope this helps!
      Thanks Rich





    • By Bigal700
      I got a 1994 yamaha timberwolf that 2 years ago i bought put carb on off a parts one had it running but not the best so i rebuilt the carb seemed to run good then i left it sit i wanted to ride it so,i took carb apart to clean it looked good had it running but wouldn't idle not a big deal then it died so i gave up on now trying to start wont do anything i checked spark looks good, has great compression and its getting gas i sprayed starter fluid in it and it still wont do anything what the heck could be wrong?
    • By Ajmboy
      View File Kazuma and Other Brands ATV110-M Service Manual
      This is a supplemental service manual for Kazuma and Other Chines brands 110 ATVs.  ATV110-M Service Manual
      Submitter Ajmboy Submitted 10/21/2019 Category Kazuma ATV  
    • By Richard Paradise
      My 1997 Beg Bear got stuck in 2nd Gear when parked on slight hill, otherwise in perfect shape. Trying to get it into neutral, by rocking it back and forth won't release out of gear.
      Any suggestions, It's my work horse and I keep it in to shape, got to get it running..
    • By StolenATV
      Loud Mini blue 4 wheeler with little orange was stolen late at night from our yard. Does not have a key only a kill switch no stickers just plane no license plate due to it not being road legal. Was seen drove on four wheeler trails in Hibbing. It was my 5 year olds birthday present and means the world to him. He’s been very upset and hurt that someone could steal his four wheeler and is so little for him to understand that some heartless people in the world do bad things And is trying to do yard work for a reward and to buy a new one 🙁 we just want our sons smile to be brought to his innocent face. Thank you for taking the time to read
      The post STOLEN ATV: BLUE RF MINI SPED STAR CLONE 50cc KIDS ATV appeared first on STOLEN 911.
      View the full article
  • Similar Tagged Content

  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...