Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Recommended Posts

I have a 1999 bayou 300 4x4 that backfires through the carburetor. It only starts doing so after warming up for about a minute...till then you can rev the motor with no problem but after it warms up a little it will not rev and bogs down and backfires through the carburetor and exhaust. It has a new stator, pick up coil and carburetor has been rebuilt. Any help would be appreciated.

Share this post


Link to post
Share on other sites


Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Forum Topics

    • 1997 Kawasaki Bayou 300 2x4 (klf300b) Runs Bad

      Hey I have a 97 bayou 300 2x4 (klf300b) that i bought for 1000 last June and sunk another 1000 into it already.  When i went to look at it, the seller had warmed it up before hand (he was riding it when I got there).  it ran good so i bought it and took it home that evening... next morning it wouldn't hardly start.  I discovered the carb was clogged, there was chunks of rust in the fuel valve, the choke lever was missing and other things.  I have since cleaned the carb and replaced the fuel valve and gas lines and cleaned out the gas tank and cap.   Enough background on it, the problem is this:  It floods if i push it past half throttle in 4th and 5th gear even going downhill and shifting correctly.  It also has to idle and warm up when you first start it which is really annoying now that its cold...  It also smokes blue smoke for about 15 seconds when started cold-  does not smoke at all once warm but the exhaust still smells like burnt metal.  A friend told me that it didn't have enough compression.  I also found out that the valves are a common cause for low compression on Kawasakis..  I have never adjusted valves before-  the most I've ever got into a engine was a head gasket on a riding mower so I'm new to this.  My goal is to get this bike running and starting cold like a top-  should i tear down and rebuild the top end?  What should i try first?  I tore the carb apart and rebuilt it and fiddled with the air screw and nothing changed.  I also ordered a compression test kit that should be coming in soon. Ive also considered just selling it for like $500 and taking the hit-  Id rather not sink too much more into this machine..  lol

      By JacobSlabach, in Kawasaki ATV Forum

        
      • 236 replies
      • 2,280 views
    • 2003 Kodiak 400 brake problem.

      As title says , my dad was given a 03 400. It didnt run. I got it running and got the front brakes working, new calipers and master cylinder.  The rear are drum and its my 1st time really messing with them. I replaced shoes , cam was all froze up so cam wouldnt rotate , i took it apart and cleaned it up good , my problem is,  how do i know where to line up the cam with the lever , there is no needle that shows shoe wear on this , its missing. Any pics or help appreciated. 

      By Bills03400, in Yamaha ATV Forum

      • 2 replies
      • 80 views
    • Kawasaki Bayou 220 - No Spark

      hi all first post just found forum and the manuals / wiring diagram BIG THANK YOU im struggling to find the vin number on my frame? I m told left side of frame , lower, nr. in front of the gear pedal ?? haven't found it yet , is it numbers stamped on the frame or a commission plate ?? main prob. no spark no power to coil , off to study the wiring info I've just found thanks again. tom

      By tomlad, in Kawasaki ATV Forum

        
      • 7 replies
      • 8,323 views
    • 1995 Bayou 220 no spark issues

      can someone tell me what could be the problem if the electric start doesn't turn the motor over but sparkplug fires like crazy but the pull rope turns the motor but no fire on spark plug. thanks for any advice in advance . cbbubby78

      By cbbubby78, in Kawasaki ATV Forum

        
      • 1 reply
      • 1,881 views
    • 1988 Kawasaki Bayou 220 Issues

      Evening folks I have a 1988 bayou 220 quad that has a damaged stator and been lying about for a few years. Recently I got the chance of a 1996 bayou 220 that had also been sitting for a few years so I decided I would try and make 1 good bike out of the 2. The 96 frame was rotten so I decided to use my original 88. I swapped the magneto and stator over from the 96 bike but then noticed that the magneto and stator wiring was slightly different so I decided best thing to do would be to change the wiring loom over. Having done this I ran into issues connecting my original run stop switch and push button start. The 96 loon had a connector with 6 wires where as the 88 had a 4 wire connector and a 3 wire connector. I sorted this by making up a conversion harness using the 2 looms but still the push button start would not work. I have now solved this by using some of the spare wires left beside the ignition key connectors and a relay. So now I have the engine turning over with the starter button. But sadly I have no spark. On checking the Cdi unit I have found that I have 6 wires going into the cdi unit but all the wiring diagrams I've seen only show 5 for the 96 model. The extra wire I have is a grey wire which has a loose unattached end beside the ignition switch. Does anyone know where this grey wire needs to be attached.  Thank you to anyone who has read this sorry it's so long but wanted to try and give the full story.

      By nwr161282, in Kawasaki ATV Forum

        
      • 1 reply
      • 497 views
  • Similar Tagged Content

  • Recently Browsing   0 members

    No registered users viewing this page.


×