Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

biggreen2010

2001 Honda Recon 250 help, possible electrical issue

Recommended Posts

ok it will start up an run but quits a lot till it gets warm, but has a bad miss an wont idle, I have a brand new Honda carb on it, good gas flow, new plug, but when I let the throttle go below a quarter, it backfires through carb an tail pipe:confused: so it has never had any electrical work or mechanical work done...it just started all the sudden, I'm think it may have ignition coil breaking down, or cdi box going bad...anyone had this trouble before? let me know what you did to fix it. thanks:skeptic:

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Chris Owens
      I have an 04 arctic cat 400 fis 4x4 manual changed the centrifugal clutch,  changed the clutch discs and adjusted the clutch. When shifted into gear forward or reverse it will leap a little but will not go it was moving with the old centrifugal clutch but it was worn out. Any help would be appriciated 
    • By MarkinAR
      I'm likely going to have to drop the swingarm on a 300FW. Are the lock rings and pivot bolts standard or left handed threads?  I looked at the service manual and it doesn't specify left hand so I"m assuming standard right handed threads.  Not sure though.  The last Yamaha I had apart was regular right handed threads but haven't had a 300 apart before.
    • By George Henry
      A clip from Diamonds Are Forever (1971) with James Bond riding a very early Honda Trike! 
      Three Honda ATCs come in at 1:54 with the one on th left pulling a sweet wheelie for 2 seconds! 
      Bond scenes are great!
    • By BuckBilly
      Good morning to all !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
      Let's see if we can make this a daily event.
    • By Dra O
      I likely just kissed $200 goodbye buying a Honda 250 this AM from Craiglist.  We'll see.
      - VIN number is off the front frame; one VIN site calls it a 2008 Honda 250 TRX - this baby ain't a 2008; other VIN sites list the VIN as invalid; might be that the owner (a shady dude from a shadier side of my home town) put a 2008 front end on it?  No idea.  
      - a HUGE hint (hint #1) would've been that there's no key to start the machine - gotta use a screwdriver.  I'll likely be visited by police sometime in the near future.
      - owner acquired from another man - owner showed me video of him riding it this summer on a major interstate while very drunk (hint #2) - the machine sounded good in the video
      - no front headlight; owner said machine has new carb - looks Chinese - he didn't have original carb; air intake box is wide open - no long plastic connection sleeve leading into air box like on my 99 king quad; no visible oil leaks; oil is dark; air filter clean; decent plastic; no front right brake apparatus; left brake handle very loose and rear brake doesn't work
      - battery at this point is good; manipulate the ignition switch w/ screw driver and the green neutral light shines (this has since stopped working)
      - it's a kick start machine: when I kicked it down (hint #3), the compression sounded normal, almost "tight"  but at the end of the cycle, there was some awful grinding noise coming from what sounded like either inside the engine or the starter area; I let it settle, kicked it again, same noise heard at the end of cycle; owner said it likely needs a new starter - I only hope it's this simple
      pictures attached - the throttle cable / zip tie pic is my favorite - but it works!  it was CRAZY dirty prior to pressure washing - and the water in air box is likely secondary to the power wash - no water was in it when purchased
      gotta few things to complete on the king quad - will be changing motor/gear oil in honda and getting new oil filter over time - talk soon - hope y'all had a great Christmas















  • Similar Tagged Content

    • By Kyboy
      Iam looking for help seperating the rear brake drum and the cover. Any suggestions would be greatly appreciate
    • By Jers
      I need to know what I have and what tire really go on it, Mine has 24x11x10 on the back and 22x8x10 on the front and I need new tire but I don't think are the right size. Also I can't find the model number listed but it looks like a 250 quadrunner 2wd and I think it is a 1987 maybe, can anyone help me, also I it has a rich running sound and I put a carb diap in it and cleaned the carb. is there a jet needing replaced?
    • By crazynordlander
      Hi All,
      I live in Minnesota and bought a 2016 CFORCE 500 HO. I am in hope to see if there is anyone in the US that is experiencing this sudden drop off in RPM below 4000 RPM. I have uploaded some videos of my issue on YouTube. I will list three of the four I posted. The fourth can be found on my channel but it is a comparison between my Polaris 570 and my CFORCE 500.
      I quit on my first dealer because we just did not mix well together. I brought it to another CFMOTO dealer that just became a CFMOTO dealer in January 2016. They are in a large ranch and agriculture area in a neighboring state that is pretty close to where I live. They have close to every brand available. They are a much larger dealer than the first one I bought the unit from.
      I brought the unit three weeks ago to them and they have worked on it a good solid week and have given up on it. I have read reports from owners in Canada that the dealers there were aware of the issue and have had success in fixing the herky jerky drivability issue.
      I am picking it up tomorrow and bringing it back home. It has been to the trails of the Black Hills this year and was new in late April. 300 miles on it. It has never changed. Very hard to ride on the trails or when I herd livestock.
      Here are the links to my videos.



      I can't accept that this is normal operation. Does anyone from CFMOTO China scan these posts?
      I need help that CFMOTO USA has not provided.
      Thanks
      Kevin
    • By sloundez
      Does anyone out there know where I can get a functional pair of wheel cylinders for subject ATV? Any suggestions welcomed. Thanks
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...