Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

dirtybear00

Need info on manual shift 2000 big bear 400 4x4

Recommended Posts

I have a 2000 big bear 400 manual shift. Does not have a shift lever on gender like a Kodiak has left foot operated rn12345 on left foot lever. I replaced the stator and pick up coil and now it is difficult to shift. I marked (indexed) the lever, rod and pivot clamp prior to removal and not sure where to go .  Maybe a clutch adjustment ? Anyone have a manual for this model ? I was sent a manual but it is for a shiftless Kodiak yet it states big bear as well 

Share this post


Link to post
Share on other sites


Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Forum Topics

    • By Christian Brindle
      I have a 2000 Polaris Sportsman 500. A year or so ago we got it running after replacing the kill switch. It ran great but after some use for a couple months it got a flat tire and for some reason we just forgot about it and it sat for some time. Before it sat i replaced the gas cap, fuel filter, fuel pump, petcock, battery, starter relay, oil and oil filter. I recently went to start it and it started so quickly and without choke or throttle but the ATV wouldn't move till about 1/4 throttle and it wasn't really a smooth ride until 1/2 throttle. it also would bog out randomly after you came to a stop and sounded like it was getting too much fuel. I cleaned the carb and adjusted the air/fuel screw to 1 3/4 turns out.  I also messed with the idle and the throttle cable adjuster up on the handlebars. It's safe to say it now runs worse than when i started working on it 2 days ago. It takes more effort to get started and bogs out idling after about 30 seconds. I tried adjusting the idle but every time i do it'll get to a sweet spot but after driving it down the driveway and back the idle will go up and down to the point where i can't put it in gear because the gears will grind. Any thoughts or ideas would be greatly appreciated. Thanks
    • By flyinbrian365
      View File 2012-13 Polaris Sportsman 550 EPS X2 Service Manual
      Full service manual
      Submitter flyinbrian365 Submitted 02/15/2019 Category Polaris ATV  
    • By Wesley Floyd
      Hey guys, Thanks for looking at my post. I haven't had a lot of experience with problems like this before, so I'm a little bit at a loss. The Quad was really hard to shift, (the dirty carb leaking gas making it idle high didn't help either). The only Idea I have would be is that the torsion spring is worn out, and that there is a normal parameter for how much it should move when those two arms of the shift shaft assembly spread apart.  That's my thought. Maybe someone who has more knowledge then me can let me know if i'm on the right track 😀

    • By colin james
      View File 2002 Polaris Sportsman 700 Service manual
      This is the factory service manual for the 02 sportsman 700 to have complete manual download all sectionset or just download  the section you need.
      Ch1 = General    
      Ch2 Maintence 
      Ch3 engine                     
      Ch4 fuel system /carb 
      Ch5 boady/ steering / suspension 
      Ch6 pvt     
      Ch7 final drive
      Ch8  transmission  service
      Ch9  brakes
      Ch10 electrical
       
      Submitter colin james Submitted 07/27/2018 Category Polaris ATV  
    • By flyinbrian365
      View File 2011 Polaris Sportsman 550 All Models Service Manual
      2011 Polaris Sportsman 550 All Models Service Manual, Full service manual
      Submitter flyinbrian365 Submitted 02/13/2019 Category Polaris ATV  
  • Similar Tagged Content

    • By Wesley Floyd
      Hey guys, Thanks for looking at my post. I haven't had a lot of experience with problems like this before, so I'm a little bit at a loss. The Quad was really hard to shift, (the dirty carb leaking gas making it idle high didn't help either). The only Idea I have would be is that the torsion spring is worn out, and that there is a normal parameter for how much it should move when those two arms of the shift shaft assembly spread apart.  That's my thought. Maybe someone who has more knowledge then me can let me know if i'm on the right track 😀

    • By pokerl0w
      this bike! did this guy sucker me or what.. ok, looks like this means something is bent that I do not see or one rod is longer vs the other?
      how long do you think this would last before it ripped into the tire? this is the right side, left side tire clears no problem

       
       
      I can not find them on www.kawasakipartshouse.com
       
    • Guest Fox300exchic
      By Guest Fox300exchic
      Indicators that tell you to check your toe-in.
    • By johncb
      My brothers 06 outlander max 400 shifter lever is very hard to get into the correct gear any ideas what the problem could be?
    • By Steve Howard
      My Hawkeye runs great just wont pull could this be the breaking clutch or the drive clutch thanks for any help
  • Recently Browsing   0 members

    No registered users viewing this page.


×