Quantcast
Jump to content

Recommended Posts

Posted

tigertaillogo

When we first got the package, we thought it seemed really heavy. After taking the TigerTail out of the box, we determined it’s really not that heavy compared to most winches and tow systems you can get out there and it seemed to be extremely well built. It has to have some weight to it, to be able to do it’s job! The Rhino is not only a fun means of transportation, it is also our recovery vehicle at  races, and any time someone finds their limits in the mud. So, we immediately took it out to the garage to go put it on the Rhino.

tigertail tow

When we first  looked at the set up we thought, “This will be interesting to get a wrench between the spool and the bottom mounting plate.“ But to our surprise they covered this, the bolts have a collar which drops into the bolt hole and holds it in place. All it took was one wrench on the bottom nut. This process took maybe five minutes. The unit easily slides right into the receiver. At this point the only down fall I have seen was, it does not come with a pin to hold it in the receiver, I was required to buy an additional one. Not a big deal but a tiny inconvenience.

tigertail rhino utvEager TigerTail to try out the, we headed out to a local ride spot to test it out. Lucky for us as we were unloading the toys when someone in an Isuzu Trooper, not meant for the mud, found a mud hole. He managed to bury his front end in the peanut butter-like slop up to the bumper. With the rear tires barely clinging to the surface by inches of hard packed dirt, he was not moving. So we thought this could be the perfect time to test out the Tiger Tail and have it be of a little assistance. I backed the Rhino up to his vehicle, and found it takes some slack on the rope before the hook will come out of the holder. As soon as the hook was free, it easily extended and retracted. We hooked it up to the Trooper and I slowly pulled forward to fully extend the rope. This being a heck of a first test for the Tiger Tail, I floored the Rhino, spinning the tires on the hard pack. To my amazement , the Rhino started inching forward and before we knew it, he was out of the slop and on to the hard stuff. We unhooked the Tiger Tail and it went right back into it’s housing trouble free.   From what we have seen so far, this is an absolutely amazing product. From the first glance of the Tiger Tail we knew it was well built and well thought out.  We know that it will definitely come in handy out on the trails and the track.  They even put a hole on the main bracket so you can still have a ball for towing on the back of your rig. Great idea! We will definitely recommend it to all of our friends. This is also one of those products that everyone who sees it wants to know all about it.  

All in all, the Tiger Tail is an awesome little product! www.tigertail.us  

Available on Amazon

View full post

 

  • 7 years later...
  • 3 years later...
Posted

It looks like only the ATV specific mounts are being discontinued, probably for the older models. I have the 2 inch receiver mount for mine so I can move it to different quads as needed. I only had to use this Tigertail a few times but it works great. 

 

Mike

 

  • Thanks 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By crankin
      I have a 1997 Yamaha Big Bear 350 4x4. It used to start right up. Then all of a sudden it wouldn't crank. I have a schematic for it so I started tracing the problem. I had no power at the starter solenoid. According to the schematic the power comes from the neutral switch and through the starter circuit cut out relay. I cannot locate the cut out relay on this machine.. If I apply power to the relay it will crank with the start button.
      The neutral switch is hard to get to with all the brackets on this thing. I did find out from all my research that if I apply the rear brake lever it will start.
      Does anybody know if the cut out relay exists and where it might be found?
    • By harryjr
      hello everybody my name is Harry jr and i recently picked up a 90's Yamaha moto4 225 i beleive and neede a starter was all he said ( i know right ) thats what they all say
      anyway i picked up a starter and installed it and when it is crankling it sounds as if it is not turning over freely as i9f there was a one way bearing not worrking correctly so pulled with recoil and it pulled back so hard i ripped out of my hand so hard it actually hurt now i have pulled and kicked a lot of bikes and such but never felt anything quite like this you can hear it try and fire and kick back but still acts as though somthing holding it back does that make any sense to anybody is it flywheel key , or valves wauyout any help would be great i picked tow of these up for $100 and tring to fix so we can ride as a family thank you in advance.
    • By joezee13
      After turning off engine in neutral  starter wont engage If I rock unit back and forth it engages Getting progressive worse.
    • By middlebrookgt
      Hi All.  I introduced myself some weeks ago with my 2006 LT-F400F that needed a list of repairs including replacing the cracked generator cover.  It is back together as of last night and cranks up, idles and revs high pretty well.  Needs some fine tuning and stop backfiring at stop.
      The big issue is it will not go into gear.  I reassembled the insides with help from y’all’s posts.  The transfer selector moves from H-L-R, and the foot shifter moves thru the gears and finds neutral easily enough.  Before I tear it back open, the  transfer selector on top does not move as far as the repair manual says.  The diagram shows the shaft moving something like 40 degrees between L and H and 50+ degrees between L and R but it doesn’t move that far even though it finds the indent areas and moves well.  
      Could this be the problem.  I aligned all the dots on the shifter gears inside and it appeared to not be binding anywhere.  I do hear the gears touching when I shift like they are trying to engage, but zero movement from the ARV
      It was somewhat difficult to tell whether all the parts are installed on each shaft.
      Are there better/bigger photos somewhere that would allow me to be confident I included all the washers and bushings, etc?  If I had any doubt on parts that were laying inside after the cover broke then I purchased replacements from online stores.
      TIA for any input or feedback!!  Pics are from when I first took the generator cover off.


    • By AnthonyT
      In search of my first ATV? What are good older 4x4 models?
×
×
  • Create New...