Quantcast
Jump to content

Recommended Posts

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Forum Topics

    • By k9_bones
      Hello, been lurking for a while fixing some of my problems after reading others unfortunate issues. However I can’t find the answers I need. Back story I have a 03 Kodiak 450. A coworker was going to take it to the dump, he said it wouldn’t run. Some mice got in there while it was stored for a few years and chewed up the wire harness. All the wheels were locked up and he didnt want to mess with it. Not knowing if it would run, for a week or so I spliced most of the wires back together. Replaced all the brake calipers and rear brake cable and rebuilt the carb. So far I have put 30ish miles on the bike and seems to run decently. Now my questions. When I put it in gear and the display light showed it is in gear I have to bump the throttle to make it actually go into drive or reverse. It doesn’t slam In gear but kind acts if you let the clutch out to fast on a manual. Is that normal, seems it’s thinking about going In gear then it goes after tapping the throttle. 2nd question, when I use the diff. Lock it acts like it is in a limp mode just by accelerating the lest little bit. It starts to sputter and won’t allow it to have any power. It only does this with the diff lock on. 3rd. The display is stuck on KMH. How do I change it to MPH. I followed all the steps I saw on YouTube with no luck. When I got power to the display it was in MPH but it switched its self and now I can’t get it back. Next are the rear u-joint the same as the front u-joints. I have sprung a oil leak from the rear diff at the drive shaft and need to replace the seal. Sorry for the long post and thanks in advance for any help. I’m sure I will find more things in the future. 
    • By colin james
      View File 2017-2019 sportsman 450/570 with eps factory service manual
      This  is the factory service manual for the 2017-2019 factory service manual for the sportsman 450/570 with electronic power steering 
       
      Submitter colin james Submitted 09/06/2018 Category Polaris ATV  
    • By JohnnyB
      Greetings, 
      Have a 88 LT80 that been sitting for a couple years. Bought a new piston, cylinder and head. Installed these, rolled it over and it quickly locks up.  Took carb apart. It was full of what appears to be 2 cycle oil. Cleaned it, but keeps locking up and 2 cycle oil continues to seap from exhaust port.  When i installed new cylinder, I noticed crankcase was full of oil.  I'm now wondering if that oil is what's getting sucked up into cylinder.  Should there be no oil in crankcase?  If that the case, how is crank and rod lubricated?  Sorry, never worked on a 2 stroke. Thanks!
    • By adr94
      Hey,
      I have an old Bruin from 2006 and I am trying to revive it.
      I am now trying to remove the last bolt on the ultramatic cover but it is turning infinitely. I don't want to force and risk breaking the cover.
      Do you know what I could do ? Do you have any tips or even was in this situation once ?
       
      Thanks,  
    • By fishhouse3
      FOR SALE: 2021 CFMOTO ZForce 800 Trail with many extras and full warranty until 2027. Only 625 miles and 50 hours of use.
      In great condition, has a clean title and one adult owner. Has had all scheduled regular maintenance and has not been abused. Only used about six times on weekend trips to Hatfield-McCoy trails in WV.
      Under full CFMOTO Care bumper-to-bumper extended warranty until 8/2027 (paid $1,600). Full service and tune up just completed with new clutch, drive shaft, belt, rollers, etc (paid $1500). Plus it comes with over $3,500 in upgrades and accessories! Way too many included items to list here (see last pics for full details).
      This machine is ready to go and needs nothing - just hop in and hit the trails!  I have over $20k invested in this machine. Priced VERY fair to sell quick at less than half that!!!
      $9,999 WITHOUT warranty -OR- $10,999 WITH full extended warranty until 8/2027.
      Located in Chesterfield, VA 23832. Message me for more pics and info!





×
×
  • Create New...