Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Ryan Hayman

Caliper Guards for Grizzly when using wheel spacers?

Recommended Posts

Just purchased 2" wheel spacers for my 2018 Grizzly. As expected, the calipers are totally exposed now. Does anyone sell some sort of guard to protect the calipers for this?

Share this post


Link to post
Share on other sites


I haven't seen anything to guard the calipers but that doesn't mean something doesn't exist. The only guards for the front end I've seen are the cv boot guards that mount to the control arms and could provide additional protection for that area. 

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Tahj
      Do I need to remove the balancer driven gear to remove the timing chain.
      If so, how?
      Thanks

    • By PolarisRich
      I thought I would make a quick "How-to" on setting wheel alignment since I was flipping my tie rod ends and I was going to have to re-align the wheels anyways.
      Here's some of the tools you will need...

      1.) Start with the ATV on a smooth and level surface, like a cement garage floor or driveway.

      2.)Center up (Eyeball It) the handle bars and lock them into place with 2 ratchet straps, one on each side of handle bars. This of course prevents them from moving when your adjusting the tie-rods.

      3.) Place two Jack Stands approximately 2 feet in front of the atv even with the outside edge of the two front wheels.

      4.) Wrap a length of string all the way around the ATV and Jack Stands, Start and end at the rear hitch. Make sure the string is the same height from the ground on all 4 wheels. I like to attach a few elastic bands to both ends of the string before attaching the string to the hitch. This makes it easier to adjust the strings when moving the Jack Stands.

      4.) Break lose the inner and outer tie-rod nuts. NOTE! Make sure you use 2 wrenches, one on the nut and one on the ball joint. Damage can occur by only using one wrench.

      5.) Adjust the string by moving the Jack Stands in or out untill the string just touches both of the side surfaces of the rear tires on each side of the ATV. This will take some time to get it right but it needs to be done!

      Check manufacturers wheel alignment specifications on your specific make and model before you adjust any components.
      For this wheel alignment I'm using the Polaris Specs which seems to be a common setting.
      Polaris - The recommended toe alignment is 1/8″ to 1/4″ toe out. This is a total amount, not per wheel.
      6.) On the front rim, measure the distance from the string to the rim at the front and rear edges of the rim. The rear measurement should be 1/16″ - 1/8″ (.2 to .3 cm) more than the front measurement.


      7.) If an adjustment is necessary, Turn the tie rod itself with a wrench or your hand in small increments. It doesn't take much to move the tire a long way, so go slow. Keep re-checking your measurement's until you have a 1/16″ - 1/8″ differance to the string.

      6.) Once your satisfied that you have the correct "Toe Out" measurements you can tighten up the inner and outter tie-rod nuts on both sides. AGAIN...make sure to use 2 wrenches.
      7.) Now take your ATV for a test drive to test your adjustments. If it still pulls one way or the other, just repeat the above steps to tweek the adjustments again utill your happy.
      The whole process only takes about 15-20 min.
    • By Tahj
      I am looking to see why my 2005 Grizzly  660 won't crank. I have set the valves but suspect a loose timing chain.
      When working to remove the valve cover I found a "cap tensioner case" - parts #25  - #299 on Babbitts site.
      The  cover seems to bridge the valve cover and the cylinder head. What the hell is it and what surprises will I  find if I remove it?
      Uncharted territory for me.
    • By David Cameron
      The small waterline insert for the hose that goes from the water pump cover to the thermostat housing has corroded off. I only need the insert on top and behind the thermostat housing that the hose goes over and can't find just the insert. It looks like it may be pressed in. I've have been told the entire motor housing needs to be replaced. The pic with the red line indicates where the hose and insert would be and the insert looks like the pic of the water pump  Any ideas would be really appreciated.
       
       



    • By Tahj
      I bought a "project" Grizzly 660, I think it has been a few people's project. The PO had it for a while and did not have time to work on it. He said the battery was good, but I don't know how he knew because the display was blank, no lights and won't crank or run. 
      I found a nest under the front cover, by the CVT inlet, a chewed thru wire and a few more without insulation. Rewired those from the connector (black 3 wire to the display) and replaced the fuse as suggested by a search from this site. That got the display working and power to other circuits. 
      I replaced the aftermarket start switch with a used OEM switch from eBay. Then it would crank a little, and started once for a few seconds. 
      I'm a small engine mechanic - mowers, snow blowers, etc. In my small engine work I have had a number of rider mowers that would crank about a half turn and then stop. The owners have suspected a bad battery and changed it with no improvement. Setting the valves to spec usually fixed this.

      I set the valves on the Grizzly without solving the crank problem. I wonder if the timing chain could be off - slipped a tooth. 
      I don't know any way to check for this without pulling the head and looking at the timing marks on the cam gear. 
      Is there another way to check for proper timing?
       
  • Similar Tagged Content

  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...