Honda Rancher 2013 solenoid issue?????
-
Similar Forum Topics
-
By Brantley11
Hey everybody,
My proficiency is with Hondas and Yamahas make me see RED!
This bike is my brother in law's, it has 1199 miles on it and went from running great to dead with no start. Every once and a while it will start and sputter for 2 seconds. It is extremely sporadic when it fires but never runs for longer than 3 seconds.
Here is where we sit:
Brand New Fully Charged battery
Carb was cleaned with air hose and carb cleaner then into the ultrasonic cleaner with Aircraft aluminum cleaner
New Shindy Carb kit (made in Japan version)
Cleaned out petcock and gas tank
New 93 Non Ethanol Gas
New Spark Plug
It gets a spark through the spark test light every time
Bluish white spark
When holding the spark plug 1/4" - 3/8" away from head it will jump and spark to the head
Good Compression
Here are the readings:
Pickup Coil 519 Ohms (range 459-561)
Charging Coil 266 Ohms (range 270-330)
Lighting Coil 0.700 (range 0.702-0.858)
Spark plug Cap 10.58 Ohms (10kohms
Ignition Coil Primary Coil 0.5 ohms (range 0.18-0.28 ohms)
Ignition Coil Secondary Coil 8.20 kOhms (range 6.32-9.48 kOhms)
Would y'all think stator and pick up coil, rectifier or CDI are the culprit?
-
By cavry
Wiring shows White and Brown to solenoid blades. Then a black wire from starter circuit relay to solenoid. I am confused, where is that black wire supposed to connect?
Thanks for any help
Cavry
-
By HoldenBoy
Hi all,
Looking for some help on a starter/bendix issue. Can Am outlander 450 2017. While cranking to start, the starter spins and engages into the ring gear. After a few seconds the bendix retracts while still spinning and there is no damaged teeth on the drive pulley. -
By Bobbywolf
I am working on a basket case for a friend. It is a 98 Big Bear (YFM350FWB). It came with a parts machine which is a 96, which I am coming to find out is VERY different from his machine.
Anyway, first thing is first. I checked compression, 150psi. Valves are set correctly, and the engine is in time. I cleaned the carb, and there was some junk in the passages. It is a chinese carb, which I figured from the lack of markings or lettering altogether.
The bike runs. It idles ok, but breaks up badly under acceleration. Pulling a new spark plug shows it is running lean. White strap, with no black whatsoever. So I have the carb adjusted with the mixture screw out way too much (about 5 turns), and the diaphragm needle lifted to the top slot. It is still not getting enough fuel (or too much air). It backfires through the carb, and cannot get above idle without carrying on. The carb boot is in good shape, so it isn't pulling any air there. I did test this as well by spraying ether around the boot when running, looking for intake leaks.
Anything big I am missing here? I am starting to believe that this chinese carb is the issue. This quad came with the original carb, which I would like to rebuild and use, but the mixture screw is totally stuck, and stripped way down in its recess.
Thanks for any assistance.
-
By jashadams
Hey all back again with my 1989 moto 4 250.
After putting a new carb on it it's really sputtery, it has new gas and I'm wondering what to tune on the carb to make it idle better. I've attached a video to describe the issue more. The bike is still work in progress but I think the video gets the point across. Thanks!
Snapchat-1142015191.mp4
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.