Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

David Irving

TRX-200 Design

Recommended Posts

I really.... REALLY... wish that whoever had designed the frame/engine for the TRX-200 had thought about giving people the ability to pull the head without having the remove the entire engine. I'm on round two of pulling this thing off / putting it back on.

  • Like 1

Share this post


Link to post
Share on other sites


In fact, I've seen at least two videos on youtube where the guy actually cuts the frame... only problem with that is my welding is worse than my attitude towards the TRX200 :P

  • Like 1

Share this post


Link to post
Share on other sites
15 minutes ago, David Irving said:

In fact, I've seen at least two videos on youtube where the guy actually cuts the frame... only problem with that is my welding is worse than my attitude towards the TRX200 :P

My welding sucks as well, cant even solder copper pipe well...😋

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By gareth leifheit
      Ive got a Big Bear 350 4x4 that has been sitting for a couple years. It was put away running but now the pull start wont move and the starter wont turn it either. Any ideas what I can lube up or bang around to loosen it up? Thanks
    • By Chris2018
      Any one know of a Mojave cylinder head out there for sale
    • By Aj Hurtibise
      I have a 2000 Honda trx90 I got from a buddy for free he said it needed a carb so I put his old carb back on it to try to get something out of it and it does not have any Spark. I already replaced the ignition coil I don't know much about four wheelers but I am a technician so I do know my way around a motor any electrical help would be wonderful or specs I don't have the best digital multimeter either.
    • By Ben Cramp
      I am hoping one of you knowledgable people can answer this for me. I have a yfm200 moto 4 engine I want to put in an off road go kart. I would like to mount a sproket where the drive exits the case before the u joint so that I can get rid of drive shaft and make engine bay compact. To do this I would mount engine 90° to axle but would also need to tilt it forward 15° to account for the angle the drive exists rear of casing. Would that be ok? Would oil pump etc still work. Any advice greatly recieved.

    • By Grant Fellowes
      Hi guys New to the forum.  i ended up here google searching for info on a bayou 300 i have here  which has a nice squeek to it. looks very much like its not getting oil fed to the head.
      it was one of 2 bayous i got hold of to add to a third one i already had here.  it looks like the previous owner had diesel in the sump instead of oil.  its had fresh oil /filter in it but develops a squeek once it warms up. ive managed to work out the oil feed to the head is not getting anything so if anyone has  a circuit diagram not just the parts manifest that would help out as im still looking for a service manual to download.
       
      Cheers
       
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...