Quantcast
Jump to content


2000 Suzuki 500 Quadmaster Fuel Issue

gmoose

By gmoose
in Suzuki ATV Forum

 Share

Recommended Posts

  • Admin changed the title to 2000 Suzuki 500 Quadmaster Fuel Issue
Ajmboy Grand Master

Ajmboy

Posted
Posted
On 10/15/2018 at 6:46 PM, gmoose said:

Fuel issue. Fuel runs through carb flooding  cylinder when sitting. Does the float suppose to shut the fuel off when sitting ?

The float is supposed to lift up when the bowl is full and stop fuel flow. If it keeps filling with fuel, you have a carb float issue I believe.

Link to comment
Share on other sites
  • 1 year later...
meinsheizer Rookie

meinsheizer

Posted
Posted

It's the needle and seat that are attached to the float actually that is the problem. Take the bowl off, pull the pin that holds the float on, carefully pull it down, check the needle tip for deformation and debris. Take a qtip and place one end in a drill and run the qtip in and out of the seat where the needle sits till its clean. Make sure when it's all reassembled that the float site level when in it's up position. Also with it fully assembled you should be able to blow into the fuel inlet port and air should pass. But if you flip it over and simulate the float being lifted then you should not be able to blow into it. GL

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • HSTAR
      1997 Yamaha big bear 350 Shift shaft issue
      By HSTAR
      Hey I have a 1997 big bear 350 4x4
      I replaced the shifter shaft and the shift arm linkage and the rod when I installed them all I was unaware that you had to line the dot on the shifter shaft with the gap on the linkage arm gap put it all back  together and rode it I can't get it to shift in the right gears  I can move the shift cam by hand and goes in different gears but with the shifter shaft in it riding I can't put it in R or N 
      Anyone know how to line up the shifter shaft and the shift cam s
       
    • Gwbarm
      Non Ethynol Fuel
      By Gwbarm
      I generally use Non Ethynol fuel in all my small engines. I just got back from the gas station and that fuel has really increased in price since last year, I will continue to use it, even though its north of 1.00 a gallon more. That seems minor compared to cleaning and repairing carbs every year. 
      I was just curious as to what others are doing in regard to gas in their quads, i know a lot of the newer ones are fuel injected which shouldnt pose a problem, but i have had lots of problems with rust and jell forming in carbs when using ethynol fuel.
    • bighoss
      2013 Polaris Outlaw 50 - Fuel Problem
      By bighoss
      i got my son new outlaw 50 a few weeks ago and we went rideing yesterday and while we were riding it died and it took me like 10 min to get started back and it died agen when we got close to truck so i pulled it back took the plug out it looked like it was drop in a bucket of gas took the air filter out and the ait box was full of gas also got home it started rite up today i started it it starter up but was blowing what look like water out of the exholst let it idel for a lil bit did not die but as soon as hit the gas and let off it will die what does that sound like i thnk i going to take it back to dealer and tell them to fix it as it is under warrenty but would like to know what it could be first
    • semicolon
      TRX350D fuel pump problem
      By semicolon
      Hi, I am having issues with my TRX350D fuel pump.  It suddenly stopped running so I have replaced all the fuses and cleaned all the terminals.  I have fitted a new pump, fuel cut-off relay and rectifier.  Still nothing!!  The pump runs when attached to a battery.  The engine will start on the choke and the filter fills with fuel but it will  not rev and dies when the choke is closed. I have power to the relay but nothing at the pump black/white wire when cranking the engine.  Any ideas where to go from here would be very much appreciated!!
       
    • ResQ91
      Help with 1987 Yamaha Big Bear YFM350FWT Carb
      By ResQ91
      Hi Guys!

      New member and could really use your advice. I would have to believe this has been an issue for others but a search here came up with nothing......? (Probably me not doing search correctly)
       
      I have an 87 Big Bear 350 YFM350FWT
      The OEM Mikuni BTM carb is shot and would rather replace than rebuild.
      It is no longer made and I have had good luck with NICHE carbs so I ordered a #K-CRB-0006 This was what they said was replacement when ordered. This Carb only uses 1 Throttle cable. The Slide is linked so it uses one. (OEM had 2nd cable coming through top to move slide)
       
      Problem is when I ordered a replacement Cable from NICHE (#C-CBL-0061) the Cable wire is a little short, not allowing Throttle to return all the way down to Idle position. I called NICHE and they are at a loss. Haven't gotten back to me after 2+ weeks.
       
      What would you recommend other than a carb rebuild?
      Can I just use 1 of the OEM cables (It is the right length) and snip/disconnect the other that went to top of Carb for Slide?
      Or ??
       
      Thanks in advance for any advice you have!!
       
      Dave

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...