Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Dan C

2000 and 2003 Yamaha Kodiak same chassis for snow plow?

Recommended Posts

Good evening   Can anyone tell me if the 2000 and 2003 Yamaha Kodiak machines have the same chassis?   I want to put a specific snow plow on my 2000 but the manufacturer dose not list a mount earlier than 2003.

 

Thank you

Share this post


Link to post
Share on other sites


I do believe they are the same and when you look at the service manual it runs 2000-2005

I updated your topic title to be more descriptive of your question 😁

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Chase Cook
      I have a Yamaha 350 in at once to try to fire up but won't. It's getting gas fire air and it has a lot of compression but still struggles to start check the timing it's top dead center valves are good valves are adjusted everything's working but won't fire I put my hand over the carb suck in gas and it tries to but it makes a lot of black smoke. Also when I put my hand over do you carb and tried to start it there's black black nasty stuff in the gas. So I don't know if it's trying to burn too much or what it is the gas tank clean and it anything to do with the gas it's with it firing. Took the spark plug out and it's pure black. What is dried up black not nasty corroded wet looking. Need help to solve the issue
    • By J Printz
      i have a 2004 Yamaha Kodiak 450 and it is losing oil but does not smoke what is it
    • By Tahj
      I bought a 2003 Recon from a kid that beat it – all plastics cracked etc, When I replaced the rear brake the inside – axle, rear oil  - were clean and in good shape, so I think Honda won the kid vs quad battle.
      It shifts a little clunky (I made the adjustment) and after riding for a while I get a hot friction material smell I wonder if he used the wrong oil and if any damage was done.
    • By Chase Cook
      I have a 2001 yamaha yfm350x and it has a brand new top end, new carburetor (stopped the leaking problem and is now getting gas to it), new CDI box, new stator, handlebar switches work, off-and-on switch works, new starter solenoid (works), new neutral relay (works), ordered a new Rectifier on its way, good strong blue spark. Has compression, valves are right. Timings is right and is TDC. When I try to start it it just makes a loud popping noise like its backfiring but it's not because its not running when I push the throttle all the way and when i barly push the throttle it try to start but won't, so I'm trying to figure out what could be the problem not starting now, Getting very fustrated with this thing and put some work and money into it and it's not still not working. This is the only atv I ever had that I can not figure out the problem to get running. Need help please..
    • By Colby Calk
      I recently got a 98 warrior 350 that 'needed the carb adjusted' but the reality is it has no spark. I have a new spark plug, plug wire, ignition coil, battery, and cdi box. I checked continuity and took apart and inspected the starter/kill/light switch on the handle bar, and it all looks brand new and checked out. The key switch seems to be working properly, as when off, nothing works, but when switched on, lights and electric starter button work. It turns over fine, and as I just stated, all the lights work. I took all the plastics off and traced all the wires, and only one had a small cut in it, but it was only through the rubber sheathing, not the wire itself (the blue one coming from the stator). I cleaned some grounds, made sure both relays work, and still nothing. I pulled the stator cover and looked at the stator itself, and it looks great. No broken wires or connectors or anything. Still, no spark. I'm at a loss. Where do I go next? Any help is appreciated.
  • Similar Tagged Content

    • By J Printz
      i have a 2004 Yamaha Kodiak 450 and it is losing oil but does not smoke what is it
    • By Dimelol
      I have a 2003 Kodiak 450 that i purchased a while back with around 300 hours on it. It has never ran right from the beginning. Initially i thought it was just a carburetor issue because it was all clogged up from sitting for months. It has been cleaned, rebuilt, and taken off probably about 10 times troubleshooting this problem. I have quadruple checked everything including float height ect and it is set correctly, the jets are also brand new, needle and seat have been pressure tested as well. So after all of that I am convinced that the carburetor is not the culprit. I have an issue where the idle is very choppy, almost as if it is misfiring with a rich condition on top of that. I can use a brand new plug and run the machine for just a few minutes and it will be a dry and and coated in black carbon build up. The exhaust also has a strong smell at idle. I had trouble restarting it when hot for a while, but i adjusted the valves and it seemed to solve that issue. They were both way out of tolerance (tight). The weird thing is, outside of idle it seems to run pretty well. 
      So with all that being said I have ruled out the carb/valves/compression and moved on to the ignition and this is where i have a few questions about factory specifications. I guess the main question I have is, how strict are these tolerances? And could them being off by this amount cause the issue I am having? Do all three of these parts really need to be replaced? I would like to know before I spend the money on these new parts, and it not fix my problem. Below I will list what the specs were in the service manual along with the reading i got.  This is my first experience testing ignition components. I just found it odd that all 3 are out of spec according to the service manual.
      Spark plug cap resistance: 10 kΩ at 20 °C (68 °F)
      My Reading: 8.90 kΩ
      Primary coil resistance: 0.18 ~ 0.28 Ω at 20 °C (68 °F)
      My Reading: Fluctuated between 0.4 - 0.5 Ω
      Secondary coil resistance: 6.32 ~ 9.48 kΩ at 20 °C (68 °F)
      Reading was within the specified range.
      Pickup coil resistance: 459 ~ 561 Ω at 20 °C (68 °F)
      Reading was within specified range.
      Rotor rotation direction sensing coil resistance: 0.085 ~ 0.105 Ω at 20 °C (68 °F) 
      My reading was 0.3 Ω
    • By Admin
      1993-2005 Yamaha Kodiak YFM 400 Service Manual
    • By Admin
      View File 1993-2005 Yamaha Kodiak YFM 400 Service Manual
      1993-2005 Yamaha Kodiak YFM 400 Service Manual
      Submitter Admin Submitted 06/29/2019 Category Yamaha ATV  
    • By Admin
      View File 2005 Yamaha Kodiak YFM 450 Owners Manual
      2005 Yamaha Kodiak YFM 450 Owners Manual
      Submitter Admin Submitted 06/29/2019 Category Yamaha ATV  
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...