Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

joninak

2017 Outlander 1000r heat problem

Recommended Posts

I bought a used 2017 Outty 1000r and have been hearing about folks melting plastics due to excessive heat near the pipe.

It's winter here & I've been plowing my drive for a couple months without heat issues. I'd like any input if this will be a problem come summer?!?

TIA

 

Share this post


Link to post
Share on other sites


Just saw this topic, but I would just keep an eye and most of the time the manufacturer will line the plastic areas with heat deterrent tape/material.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By MarkinAR
      And the new 300FW is already wounded. Something got in a bind and blew the whole chunk of case out around the primary drive gear at the back of the motor. In the pic you can see the crack along the top...there is a big chunk missing from the bottom. And it won't roll....but the front and rear diffs both seem fine. Unfortunate. This looks to be a bit of a project. Still feels like it will shift through gears so i'm wondering if the ring and pinion just jumped a bit and blew something to pieces.  I have a parts bike.  But will this require the case to be split and transmission completely disassembled?  I assume you can't just slide the broken primary drive out and slide the replacement in?
       

    • By Bruce Sawyer
      1987 YFM350FWTB 350 4x4 Big Bear when going uphill will sometimes act like the clutch realeases then re-engauge all at once.
      Seems to maybe be little more often if the engine is at about 1/2 throttle instead of at lower rpms.
      I have the Factory Service manual and checked the external clutch adjustment screw as ok and the H/L/reverse shifter lever linkage as adjusted correctly. It appears to be maybe a internal (inside the case) clutch issue or ??
      This is the type Big Bear that has the manual shift lever on the left front fender and has the manual foot shifter lever with 5 speeds forward.
      Can someone tell me how the primary and secondary clutch operates? 
      I assume one is mechanical and one is centrifugal. (what I'm asking is one clutch for the higher rpms and one for the lower rpms or ???. (the clutch appears to only momentarily release at the higher rpms is why I ask. The cycle has about 3000 miles of low speed through the brush hunting and has been well maintained, oil changed, etc and no deep water or mud useage.
      Anyone been into a similar issue with the big Bear ATV????
    • By colin james
      View File 2017-2019 sportsman 450/570 with eps factory service manual
      This  is the factory service manual for the 2017-2019 factory service manual for the sportsman 450/570 with electronic power steering 
       
      Submitter colin james Submitted 09/06/2018 Category Polaris ATV  
    • By JacobSlabach
      got 7 atvs off CL recently for a good price.  one of which is a yamaha warrior.  anyone know where the vin is printed on this bike?  Haha good place to start as I do not know year or size yet.  The former owner says needs exhaust ans and clutch work.  he said it ran fine until the clutch cable broke and then I couldn't get the new cable adjusted right and it would grind gears.  things I see:  clutch cable locked up again, no brakes, carb leaking (green with algae around the bowl and has gelled gas stalagtights on it), aftermarket exhaust melted the airbox so I need something different and a new air box.  I would like the use the current exhaust if I can but I have a feeling its a redneck fix as it looks like there is an ace bandage holding it to the exhaust pipe (its an aftermarket slip-on exhaust), so I'm not sure about that- lets get the bike running first.  also, battery (looks brand new, what a shame) is dead, 0 volts.  Otherwise, bike looks to have not been wrecked, and plastics are ok (it sat outside under a 'tarp' for 3+ years since it was run last).  any tips and advise on where to start first would be awesome as this is my first clutched bike (manual).
      the clutch is my main concern- I've never rode a clutched bike so I dont even know what its supposed to feel like.  lol I'm spoiled on my automatic polaris 
    • By Barry Troxtell
      I have a 2005 Sportsman 500, Instrument cluster will not illuminate, hi/lo beams work though.  Any tips or troubleshooting info is greatly appreciated!
  • Similar Tagged Content

    • By Ssg
      Hello! This is my first bike with a cvt it's a 19 Outlander 850 xmr. I use the 30" cryptid tires that come with the bike during hunting season since I hunt in a louisiana swamp and I have some 27" interco reptiles during the summer trail rides. So this past hunting season I got stuck and squealed the belt do i looking at cluch kits /adjustments to help with the low end but I dont want to mess with my summer riding so I'm looking for advice 
    • By Brian T. Aichinger
      I have a 2017 can am 570 outlander max that is having issues with the powersteering going out and the speedo quits working. anyone else having or heard of these issues?  everything else on the display cluster is working and I hear no noises as far as the powersteering unit, the dealer did change the steering unit because of the recall.
    • By Chris Abshire
      Changed fuel pump, has spark and good compression. Tried a gravity feed trick and still couldnt get it to fire off. But it does try to crank when i spray starter fluid. With pump connected and fuel hose off, it should still pump fuel, correct ? But its not. And i cant find anything online about this bike. Has less than 200 hrs, so barely gets ridden (wifes). New fuel in tank. Any suggestions would help. Thanx....
    • By Ajmboy
      View File 2013 Can-Am Outlander & Renegade Service Manual
      2013 Can-Am Outlander & Renegade 500/650/800R/1000 Service Manual
      Submitter Ajmboy Submitted 01/28/2019 Category Can-Am BRP ATV  
    • By Ajmboy
      2013 Can-Am Outlander & Renegade 500/650/800R/1000 Service Manual
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...