Quantcast
Jump to content

  • Do you own an ATV, UTV or SxS? Join our Community Forum!

    QUADCRAZY ATV Community and Forum are FREE to join! We keep our ATV, UTV, and SxS forums clean and user friendly. All first time posters in our forums will have to wait to have their content reviewed and approved. Once your first ten posts are approved, you will no longer need to go through a forum post approval process. To bypass the approval process with immediate access and a NO ADS experience in our ATV, SxS, and UTV forums, consider subsribing to a Premium Membership

Learn to be an ATV Mechanic


Ajmboy

Recommended Posts

You can take part in home study at Stratford Career Institute:

Motorcycle/ATV Repair Module 1

Introduction to Motorcycles and ATVs

· Styles and designs

· The engine

· Overview of systems

· Shop safety and environmental protection

· Tools, measuring instruments and shop equipment

· Fasteners, gaskets and diagnostic procedures

· Basic electrical and electronic theory

· Four-stroke and two-stroke engines

Motorcycle/ATV Repair Module 2

The Major Systems and How Each Works

· Fuel systems

· battery and charging systems

· Ignition systems

· Lubrication systems

· Cooling systems

· Exhaust systems and emission controls

· Power transmission systems

· Wheels and tires

Motorcycle/ATV Repair Module 3

Maintenance and Overhauls

· Brakes

· Frame and suspension

· Accessory systems

· Engine and power transmission disassembly

· Two-stroke engine overhaul

· Four-stroke engine overhaul

· Power transmission overhaul

· Tune-up and general service

· The business of motorcycle, ATV and scooter service

Motorcycle /ATV Repair Module 4

The Motorcycle Workshop

· Tool usage and workshop techniques

· Engine and transmission related tasks

· Frame and suspension related tasks

· Electrical and ignition related tasks

· Oils, bearings, seals

· Fuel, sparkplugs

· Torque settings and drive chains

· Electrical equipment

Motorcycle/ATV Repair Module 5

ATV Repair

· ATV terminology

· ATV buyer’s guide

· Tools, safety, and accessories

· Brake systems

· Fuel and exhaust systems

· Suspension, steering and frame

· Electrical system

· Tires and wheels

· Engine maintenance

· Clutch, transmission and final drive

· Cleaning, storing, and transporting the ATV

· Troubleshooting

Visit http://www.scitraining.com/Courses_US/Motorcycle_ATV_Repair/Course.htm

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By gatorschevy
      If so, I have covid lol, in the past 3 months I have bought 6.
      04 Suzuki Quad runner 400
      86 Kawasaki bayou 185
      96 Polaris magnum 425
      95 Polaris trail blazer 250
      03 bombardier 175 rally
      92 Yamaha moto 4 350 
    • By kiriyaaoi
      Hello everyone, I just picked up an 02 LT-F250F the other day and have been in the process of tearing it down to fix some stuff- one of which was the cylinder base gasket leaking like a sieve. Well, I know why that is now, and I also discovered that someone had been in there before. I didn't take pictures, but it looks like it was probably run low on oil at some point, the cam journals and the "bearings" (for lack of a better term) in the head and the valve cover are totally wiped out, very deep grooves.  From what I know it's very difficult to repair aluminum in this way, so I'm trying to figure out where to go next.
       
      1. Have someone grind down the head and valve cover and fit actual bearings in since the aluminum is screwed, and have the cam ground down to match.  I have no idea what this would cost.
      2. Buy a replacement head+cam+valve cover.
       
      #1 I was hoping someone might have some advice on, but #2 seems like it'll (probably) be the more cost effective option.  However I'm running into some difficulty, it seems like the 2001 and 2002 models specifically use a different head part number,  11100-19B10, instead of  11100-19B01 like for all earlier models.  What exactly is the difference between them? There are obviously far more of the earlier heads because it ran for over 10 years.  Are they actually interchangeable? I've also noticed there are heads from the LT250EF that has 4 valve heads but also otherwise look identical.  Would those work as well possibly?  I'd like to not have to drop $500 on machine work or new heads on a $1300 quad that I'm already putting a bunch of new parts on.  Oh, and it has a new piston and the cylinder itself looks pretty good too, as I said someone was in here before me.
       
      Any help or advice would be greatly appreciated. I'll post pics of the carnage tomorrow.
         
       
    • By Sofaspud
      My 2008 can-am Outlander 800r is having hard shifting issues. Does anyone have a fix for this ?
    • By Am2007
      Hi everyone,
      Outlander 2006 400 XT i have replace the startor cover and right after i did that the oil light is on and not turn off, i check the wires and checked the oil level, everything seem to be normal quad is starting without any problem and rev just fine. i did not want to ride it since im not sure if it is faulty sensor or not so just be safe i did not let it run more the a minute or so. 
      I have read in the owner manual that i need to clean the oil strainer every 200hr unfortunately i never did that, my service manual that i have does not even indicate of such a thing. so i did some search around and it seem like canam split the manual into 3 parts
      owner manual
      service manual
      engine manual
      I have the first 2 but i can not find the last one, part number 219100232. If someone can guide me where do i find the oil strainer so i can clean it i will appreciate it.   im going to do an oil pressure test tomorrow to check how many PSI i have, just to make sure.
      Thanks
    • By Roofus
      I cant seem to find what this part is called. Can anyone point me in the right direction? I must be misinterpereting the parts catalog or something? I dont see it in the rear axle section. I think it may be in the rear brake assembly section? click link to view picture.

  • Similar Tagged Forum Content

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...