Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Eddie Lambert

03 Cannibal vacuum hose to engine

Recommended Posts

So I picked up a Cannibal that has been sitting for many years. I wonder if anyone can tell me where that vacuum port is on the engine. I’ve found the one to the air box, pressure regulator, and ecu but can’t seem to locate the one on the engine. Thanks in advance for any help. 

7AC0269F-99C6-4A9C-9C77-59F3CCF1D993.jpeg

Share this post


Link to post
Share on other sites


I haven't seen much in these forums on Cannondales. Weren't they discontinued? Nice quads though. There's only this one manual in our downloads (wish we had more)

 

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Mike Iadonixi
      Hi my son's 2005 Honda recon engine is seized any ideas on what or where to get another engine 
      Thanks to you guys i fixed my other son's four wheeler last month
      any help would be greatly appreciated
      Thanks
      Mike
    • By David Land
      About 6 months ago I had a new fuel pump, ECM, stator and heaven only knows what else installed on my 05 King Quad.  It has been running great until the other day when I went to get it off the trailer, and it would not start.  Pulled the plug, and it was a little dirty, but not bad, but I put a new one in just for good measure.  Still would not start.  Pulled the fuel line connector underneath and turned on the switch and fuel was coming out, but with little to no pressure.  I turned the switch off and on multiple times to fill up a water bottle with fuel, and the fuel was good.  As it turns out, the fuel pump is out of warranty (go figure).  So, I'm going to put a pressure gauge on it tomorrow and see what it is pumping.  Is there anything else I can check?
      Many thanks,
       
      David
    • By Gilbey
      Does everyone run the tire pressure as stated on tires or perhaps a couple # below to soften the ride a little?
    • By Christopher Middleton
      I was given a "Go-Kart" its an old Carter brothers dlx150 but the engine is not the same that came with this Kart. I am trying to ID it so i can look at getting some parts for it. the pictures attached are of the motor and the only ID marks on it. I am thinking its some sort of 200cc from the 1980's does anyone have a better Idea? I am really trying to get a rebuild kit for the carburetor. on the carburetor is  Keihin 63 AA YKT

    • By Jacob Dellinger
      Pressure testing a Polaris 250 trailblazer with motion pro tester. Atv leaks down from 6 psi to  3 and hold there and I can’t kind a leak with water and dawn soap. . New to pressure testing a atv but have done 100s of saws etc. was going to order clutch puller and flywheel puller andCheck seals. Also notice that there is a clutch alignment tool, do I need this if i pull clutch? 
  • Similar Tagged Content

  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...