Do you own an ATV? Join our Forum!
As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery. Registration is fast and you can even login with social network accounts to sync your profiles and content.
Friday evening went riding, rode for a good hour or so everything was fine. I went to take a short ride to the restroom (less than 100 yds away) and all of the sudden everything flickered and then just died out. Accompanying the problem I noticed the killswitch completely locked up. Once daylight hit took the killswitch apart to find it had shorted out and melted the plastic inside. Has anyone else had anything similar to this and if so what did you do to fix the situation? I have a new killswitch on the way to replace the obvious problem but was wondering could there be a bigger issue at hand. We tested with a voltage meter to make sure everything was still getting power from the battery and as far as we could tell it was.
Any advice/info would be GREATLY appreciated.
By colin james
View File 2017-2019 sportsman 450/570 with eps factory service manual
This is the factory service manual for the 2017-2019 factory service manual for the sportsman 450/570 with electronic power steering
Submitter colin james Submitted 09/06/2018 Category Polaris ATV
Headlights on my Outlander 570 are junk. Would like to upgrade to a light bar. What is the max size (wattage) that it can handle?
Can I just split into the high beam wire for an install. I see YouTube videos of a separate switch that hooks up straight to the battery, but wouldn't that drain the battery if the machine is off and lights cold be left on by accident.
I'd like to hang it from the front rack as I have a basket installed on the rack that I would like to keep there. If anyone has done this, please send a picture!
I recently purchased the subject UTV for my kids. It's my first Polaris (other wheeler is a Teryx4) - and my first-ever single-cylinder vehicle (even my mower has more)...
Valve lash adjustment values... The operating manual recommends verifying at specific intervals, but does not provide the clearances or procedure. Any idea where I can obtain those? Tach on the display shows about 1500RPM when at idle, and about 6000 when WOT at max speed (30MPH). Does that seem correct? The engine does not SOUND like it's going that fast, but that may just be my unfamiliarity with single-cylinder engines. The idle feels mildly rough - and the tach shows a fluctuation of about 50 rpm. It's not wild, but it is noticeable. Again, without any point of reference, I do not know if that's just the nature of the beast, or if I should be concerned. The front wheels spin freely in the forward direction (mild brake noise can be heard), but when rotating tires backwards, the brake pads grab the rotor with significant force - making it nearly impossible to turn the rotor by hand. Considering the cost of new rotors and calipers, I'm hoping there is a know 'fix' for this issue. Any help would be appreciated! My kids can't wait for me to give it the "all clear". Still waiting on helmets to arrive from Amazon, so I have a couple of days to get all the maintenance and repairs completed.
I just bought this thing and got the carb all cleaned today and it was running like a champ. There was a spare hot wire hanging down that was not hooked up to anything. I found it when I took all the covers off and did the carb work. Unfortunately I forgot it as well when I fired her up after cleaning and replacing the carb. While I was running her, the wire was lying across the exhaust pipe. The exhaust got hot, melted the insulation and next thing I know I see sparks flying everywhere Bike immediately shut down and all lights went off. I have nothing on the console now when I turn the key over. I fear I have fried my ECU. I found one fuse back by the box, a 30 amp, but it was good. Are there any other fuses on these things? Is there a way to test the ECU? Could it be the rectifier or voltage regulator?
Recently Browsing 0 members
No registered users viewing this page.