Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Sign in to follow this  
StolenATV

STOLEN ATV: Arctic Cat ATV Stolen in Wayne County Tennessee

Recommended Posts

A subcontractor working on the property stole numerous items including the 4 wheeler. The trailer, welder and chainsaw was recovered at the individuals residence. The 4 wheeler has not been recovered. Ive had this 4 wheeler since 2000, all of the children have enjoyed riding it. I would love to get it back.

The post Arctic Cat ATV Stolen in Wayne County Tennessee appeared first on Stolen 911.

View the full article

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Sign in to follow this  

  • Similar Topics

    • By cfauvel
      ok help so according the service manual, Idle Air Mix Screw (aka Pilot screw) should be initially set to 2.5 turns out from fully seated.

      If I do that the motor doesn't want to start or stay running...right now the pilot screw is probably somewhere near 5 turns out....I'll take the carb off tomorrow to count to know for sure.

      mind you the carb got a new float seat,float needle and various other components in the kit.

      To get the motor running I hard to turn the pilot screw out quite a bit, and turned the idle speed screw in quite a bit...I didn't hook up an inductive tach to know what it is idling at, but does sound about right.

      What should the idle speed adjustment screw initially be set at (the one that has the black cable sheath with a knob you can twist easily)?

      Is there a special tool to turn the idle/pilot mix screw whilst the carb is on the running motor? I am using a slotted screw driver bit (normally goes into a driver) by hand..makes it hard to turn the driver and hard to tell how many turns .
    • By YamahaBB350
      I have a Yamaha Big Bear 350 and the reverse doesn’t work, it shifts from low to high easily but it won’t go back to reverse. I’m new to this stuff, so I’ll take any help. Any ideas? 
    • By Scott Sirr
      I need to figure out how to clean/fix or replace my neutral switch assembly On my 2008 Yamaha big bear 400 as generally the neutral light doesn’t come on when it is in neutral. To get it to come on I have to wiggle the foot shifter and hold it in just the right spot.
      I have googled it and can’t find much on the 400’s. I can’t find a service manual online and the parts manual is super vague.
      I think it is in the right side engine cover area, but not certain. 
       Any help would be great. thanks
      Scott
    • By Mike Johnson
      Does anyone know what the 3rd item is behind the battery on this ATV ? I know 1 is the,  solenoid1 is the CDI box, what is the 3rd.
    • By Mike Johnson
      Hello again guys ,. I have a Quadmaster that has a very bad lean to my passenger side wheel. I replaced the a arm bushings with no change in the lean,  I see no bent parts and no adjustments available. It's always been there since I got it but became really noticeable when I put the lift kit on it. I'm going to add a picture of the problem if allowed.

  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...