Quantcast
Jump to content

Recommended Posts

Posted

So I’ve rebuilt this quad and the only issue is fuel delivery. The filter fills up then runs out of fuel then dies. I’m thinking that vapor lock is the cause. And here’s my reasoning. The fuel lines are supposed to be 3/8 are 5/16 on there and it looks to have a huge filter on there. I did blow out all the lines and checked the petcock as well as the screens in the tank. Sonic cleaned the carb and replaced all the jets and needle. Blew out the vent lines too. Any one else have thought?

 

 

Sent from my iPhone using Tapatalk

Posted

It’s possible about the fuel line thickness but I don’t think it’s likely.  I would remove the fuel filter and run a direct line to the carb without the filter. Just to see how it runs.   The filter is directional so it should go on the line on the right direction, have you checked that also ?

Posted

Yes. When I was shooting air thru it it’s clear all the way to the carb. The carb is clear also. I took the cap off the tank just to rule that out too


Sent from my iPhone using Tapatalk

Posted

It’s the same thing that happens with the filter. Runs great then dies. Ill show you guys what I’m talking about in a few minutes.

It’s awesome to be back. The quads took up some time. I have something else I’m working on too that will be custom and awesome.


Sent from my iPhone using Tapatalk

Posted
It’s the same thing that happens with the filter. Runs great then dies. Ill show you guys what I’m talking about in a few minutes.

It’s awesome to be back. The quads took up some time. I have something else I’m working on too that will be custom and awesome.

I’ve been doing okay. Got a lot things under control. I’m coming out to L.I.C next week. Have a few things to do down there. Let’s meet up and have a beer.


Sent from my iPhone using Tapatalk




Sent from my iPhone using Tapatalk
Posted

Yeah. Smaller lines and filter fixed it. But now it’s a ping at low idle and goes away when you rev it. It’s all new besides the dome. I don’t suspect piston slap. Give me a text frank. New phone.


Sent from my iPhone using Tapatalk

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Popular Now

  • Similar Forum Topics

    • By Joeguy
      After i did my rebuild it seems to not want to shift well. I think the cable is alright, and when it does shift its nice and solid. I have to basically use my hand to shift and i have to pull or push it very far, like max travel, to get it to shift. I also tried adjusting the clutch set screw. Any ideas where to go next, or maybe i should just grab a new cable to try.
    • By Dsluder
      I am having an issue with a hs500. I bought it broken and have been trying to get it running. It seems to be starving for fuel. If I put my hand over the intake it will crank but will not run for very long because I'm not able to get the correct airflow with my hand. The things I have done so far are. Replaced the fuel pump, fuel filter, mass airflow sensor, idle air adjuster, fuel injector, cleaned the throttle body, replaced the ecu, and still the same issue. I notice the injector does not spray when removed from the head. I dont know if that is common. 
       
      I am out of ideas on what to do next. I have removed the fuel line from the injector and it is getting plenty of fuel. If anyone has an idea on what could possibly be the issue I would be happy to try anything at this point.
    • By Maxg_57
      Is anyone still active on this club
    • By Mikey509
      Hi everyone, first and foremost, I want to thank everyone for all the help I've received. I am so glad I found this community. I also wanna apologize if I'm spamming the forum, I come up with questions as I go, I guess lol. So when I got my Recon, the air box was missing the lid, held together by zip ties, and the filter was ripped and nasty. I have since ordered a new air box assembly. It comes with everything: the box,  lid, and filter ( the insert and the foam), and all the hardware necessary. This is the first time I've seen a metal filter inside a foam filter lol. However, my question is, I have read that you have to oil these filters? Every time I read it, it was always skimmed over, and I could not remember where I had read it. Is there a certain oil needed for this? Is the filter washable and reusable? Do I just stick the filter in oil, lol? Sorry if it sounds like a dumb question. Thanks in advance, y'all!
    • By Jdeaton011989
      Hi all. I have a timberwolf 250 2nd that will not start.. I thought it was out of time bc the guy I got it from said it just quit on him. The tensioner had a nut welded to it and it was like2 teeth off. I installed new tensioner and chain and it still will not start. It has fire and it will not hit off brake cleaner. It has compression. Haven't put a gauge but I'm sure it will crank and run with what it has. I double checked my work and it's still in time. Spot on. Both valves move. I'm about to put a feeler gauge on them and I'll cone back but other than that any ideas?
×
×
  • Create New...