Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Ryan Foster

2002 Suzuki KingQuad 4WD (LT-F300F) Engine/Model ID

Recommended Posts

I am trying to find a used OEM cylinder for the above mentioned quad. I was told the current cylinder came from Amazon so I suspect its aftermarket china (made from recycled coat hangers and shopping carts.) Anyway, was looking at the parts list and they have 2 cylinders listed..
11210-19B82-0F0
MODEL X/Y
and..
11210-19B90-0F0
MODEL K1/K2

My engine case is stamped K403 230829 Trying to figure out what model I have. I see I have a K in there but....
I don't know what the differences are between the cylinders (the first one cost more). Anybody know how to decipher this?
I only have the engine, I don't have the frame to get the actual VIN.  


Also, are there any marks on an OEM cylinder to differentiate it from aftermarket?

 

Share this post


Link to post
Share on other sites


Thanks for the link.  I am thinking I am going to just work with what I have and send the cylinder off to Powerseal or Millennium and let them repair it and be done with it. 

  • Like 1

Share this post


Link to post
Share on other sites

Always the best idea.  The imported cylinders are soft and only last for a bit.  For a quick low buck flip I'll do them before paying machine shop prices but for one I'm keeping I'll just hone it a bit if it's not worn smooth out or punch it a smidge and rering. 

  • Like 1

Share this post


Link to post
Share on other sites

I kept seeing kits with a Namura top end set and a cylinder.. I finally went to their site and couldn't find a complete kit with a cylinder, just the top end parts.  I contacted them and they said they don't offer cylinders and that any kits I see are pieced together but not by them.  Other than the Namura kit, I wasn't able to find anything else like that so I'm going to "assume" this is an oem cylinder.  Powerseal told me OEM was cast iron sleeved and this is cast iron.  I can run around town dealing with a local machine shop but just to be done with it, going to send it probably to Powerseal since I have used them before and they were a little cheaper than Millennium and that bike is still running fine after 7 years. 

Edited by Ryan Foster

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By mothrottle
      Does a US made grease gun fit Metric zerk fittings, or do I need a conversion to fit them?  Thanks in advance.
    • By JacobSlabach
      I have a gentleman that asked me to service his bayou for him.  I have always wondered what oil should be used in atv engines?  Pros?  Cons?  What weight should be used in what type of weather?  Is there one kind that I could bulk buy and safely used in any quad I worked on or owned?  What about performance?  Engine Life?  This has always been a 🤔🤔🤔 area for me with quads as far as why you would use one type of oil over another....
      Thanks!
    • By Dwight Williams
      Ok, so I bought this scream of a deal the other day - a 94 King Quad 300 for $40.00.  It's been sitting outside with no carburetor on it for about a year.  Its rusty, missing some parts, wiring is all cut up and spliced etc.  No seat, no racks but the plastic is all there minus the headlight housing.  Anyway, who can pass up a $40.00 quad right?  I get it home and looked at the sight glass for oil level, it's about 1/2 oil and 1/2 water.  I drain it, refill it and turn the motor by hand (recoil starter is missing) and it turns over just fine.  I worked on the wiring for about an hour and got it to turn over with the electric starter and got enough of it sorted out to get a spark.  Did a quick compression test, 70 lbs.  Wet test bumped it up to 90.  Ok, so rings and cylinder washed out with water for a year, not too surprised.  I thought 'what the hell' and sprayed some starting fluid in it and it ran for about 2 seconds - enough to show  it's got life.  Since then the compression has gotten worse, I can't get enough pressure to activate the carb diaphragm, therefore no fuel pump either.  The compression is now around 60.
        Anyway, my question is....is it worth it to try to get this thing going?  I tore the top end down today and the cam and one of the rockers is pretty worn.  I figured a top end job would be about $100 or so, depending on the condition of the cylinder but I'll probably have to put a cam and rockers in it as well.  Doing some research on ebay I figure I'll have to spend about $500-$700 to make the whole machine right again.  Much less just to make it run and use as-is but I won't really like it until it's right.  I don't mind doing the work, I actually enjoy it but I'm concerned about what all that water did to the rest of the internals, I can't really test it all out until I can make it run.
      I know it's a basket case but I'm not into it much at all, even if I do the top end and find something else wrong I'm still not out much.  I'm leaning toward ordering the top end parts and going from there unless you can convince me otherwise - any way to check the rest of the internals without tearing it down?  I plan on flushing the oil cooler before I do another oil change, I've drained it twice now and it gets milky almost immediately just turning the starter - I suspect the oil cooler is polluted badly.
       
      I'll get some pictures today if anyone want to see them.
       
      thanks!
    • By William Edwards
      Hello,
      I'm new to the site.  My son and I have decided to bring back our old quad from the dead.  Does anyone know where we can purchase a cylinder kit for it.  I think it's a 1986, but will have to check the VIN to be sure.
      The last time it ran, it was tapping and smoking pretty bad.
      Any help would be appreciated.
      Thanks!
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...