Quantcast
Jump to content

1990 Yamaha Big Bear 350 4X4 Timing Chain

WIJBIRD

By WIJBIRD
in Yamaha ATV Forum

 Share

Recommended Posts

WIJBIRD Apprentice

WIJBIRD

Posted
Posted

Looking for a guru to help me get the top end back together. I'm stumped!! There seems to be an issue with the removable chain guide on the left hand side. In its current position (which is probably incorrect) there's not enough clearance to get the chain on the sprocket and be able to line up the timing. Does the guide rest on the side or is it supposed to be in the notch underneath? I have a manual, but it doesn't show the correct positioning on that guide. I tried to fit it in the notch, but then the cylinder head doesn't seem to seat properly. Let me know if you need pictures. Any help (and pictures) you able to provide will be greatly appreciated.

Thanks in advance!!

Jay in WI

Link to comment
Share on other sites
MarkinAR Experienced

MarkinAR

Posted
Posted

If it's like the 93 Kodiak I had apart recently, there is a valley at the bottom of the front (not adjusting) the timing chain guide goes in to.  The top of that adjuster just kind of "sticks up" into the rocker cover.  It seems that I got the front guide in a bind and noticed that it touched the chain so it sounds like you've done that also.  Just have to get it seated right, may have to lift and lower the head a dozen times and then it just magically sits down cleanly.

Link to comment
Share on other sites
WIJBIRD Apprentice

WIJBIRD

Posted
  • Author
Posted

Here are two pictures. If you look at the lower left corner of the sprocket (I know that circles don't have corners), you'll see the top of the black chain guide. Is it suppose to tuck into that little "pocket" in the cylinder head? I tried that once, but then the cylinder head wouldn't seat. What do you all think?

Thanks!

IMG_2030.jpg

IMG_2029.jpg

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • Mhatayas
      Baja 250, No Spark , I'm stumped ...
      By Mhatayas
      My uncle bought a Baja 250, 2006. Knew there was no spark since the get go. He don't know anything about quads so is getting me to help him try to get it running...
       
      battery is bad so I connected battery charger to it to crank it over , cranks over well , but no spark .... 
      Lights and everything work fine , but with each crank over using the e start switch , the display reads 999 888 777 666 ... Right down to 000 and repeats itself . 
       
      He managed to get a parts bike , I changed over the CDI and the coil and the stator from the parts bike and there was another black box by the voltage regulator I changed over ... I used my multimeter to confirm as much as I could works , it's hard without knowing which wires are which , and I cannot find any diagrams online for this bike ? 
       
      Do you think it could be the Killswitch? There's so many wires coming from there I don't know where to start . Also I should mention it appears the fan on the front of the bike has been taken off (the wires have been cut too ) 
       
      If this bike sparked it would run . The previous owner said he parked it one day and it just wouldn't start after.
    • ResQ91
      Help with 1987 Yamaha Big Bear YFM350FWT Carb
      By ResQ91
      Hi Guys!

      New member and could really use your advice. I would have to believe this has been an issue for others but a search here came up with nothing......? (Probably me not doing search correctly)
       
      I have an 87 Big Bear 350 YFM350FWT
      The OEM Mikuni BTM carb is shot and would rather replace than rebuild.
      It is no longer made and I have had good luck with NICHE carbs so I ordered a #K-CRB-0006 This was what they said was replacement when ordered. This Carb only uses 1 Throttle cable. The Slide is linked so it uses one. (OEM had 2nd cable coming through top to move slide)
       
      Problem is when I ordered a replacement Cable from NICHE (#C-CBL-0061) the Cable wire is a little short, not allowing Throttle to return all the way down to Idle position. I called NICHE and they are at a loss. Haven't gotten back to me after 2+ weeks.
       
      What would you recommend other than a carb rebuild?
      Can I just use 1 of the OEM cables (It is the right length) and snip/disconnect the other that went to top of Carb for Slide?
      Or ??
       
      Thanks in advance for any advice you have!!
       
      Dave
    • Gwbarm
      Looking to buy a new SUV
      By Gwbarm
      I have been exploring all the options available, so many, its hard to choose. I have kind of narrowed it down to the Honda Pilot, Subaru Outback, and Kind of looking at the Outlander, although its a little small,  the new one is nice looking. Just wondering if anyone has any recommendations or gripes with any of these rides. I have driven Jeeps for the past 25  years and they have been great, but their price point has gotten to high. Expieriences good or bad would be helpful. Thanks!
    • Tuzz
      1990 Suzuki King Quad 300cc Kicks and bucks when accelerating unless ignition switch is in LIGHT position.
      By Tuzz
      Bucking started about a month ago and works ok after 1/2 hour warmup.  Today while working on it i discovered that if i put the ignition switch in LIGHT position it runs fine right from the start.
      I'm stumped!  Any idea why this could be?  

    • HSTAR
      1997 Yamaha big bear 350 Shift shaft issue
      By HSTAR
      Hey I have a 1997 big bear 350 4x4
      I replaced the shifter shaft and the shift arm linkage and the rod when I installed them all I was unaware that you had to line the dot on the shifter shaft with the gap on the linkage arm gap put it all back  together and rode it I can't get it to shift in the right gears  I can move the shift cam by hand and goes in different gears but with the shifter shaft in it riding I can't put it in R or N 
      Anyone know how to line up the shifter shaft and the shift cam s
       

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...