Quantcast
Jump to content


400ex with 450 carb??


Recommended Posts

So I’ve got a 2000 Honda 400ex absolutely love it!! I’ve had it for about a month, I ride with bruteforce 750’s, outlander 850’s and 1000 sxs’s and I was thinking of getting a trx450r carb and a full hmf exhaust. And probably doing the air box mod too, how much power would this give my 400? Just a little different or a big difference? Cuz if it’s not much of a different I’ll just stick with my dg slip on..... thanks!

Link to comment
Share on other sites

In terms of percentage increase not much. 450 carb could make it a little snappier but its probably not worth the expense. HMF slip on is not any better than DG, however changing the header does help. It'll run a tad harder. What airbox mod do you mean? Most folks chunk the lid and that's stupid for anything but race. the last one I had we blocked off the intake with a krylon can and poked holes in the lid. it could still breathe but got cleaner air under the seat. No increase, just preference. 

Also, any changes in intake have to be reflected in fuel increase. Larger main jet is necessary for more air flow. 

Link to comment
Share on other sites

  • 4 weeks later...
On 6/17/2020 at 11:40 PM, MarkinAR said:

In terms of percentage increase not much. 450 carb could make it a little snappier but its probably not worth the expense. HMF slip on is not any better than DG, however changing the header does help. It'll run a tad harder. What airbox mod do you mean? Most folks chunk the lid and that's stupid for anything but race. the last one I had we blocked off the intake with a krylon can and poked holes in the lid. it could still breathe but got cleaner air under the seat. No increase, just preference. 

Also, any changes in intake have to be reflected in fuel increase. Larger main jet is necessary for more air flow. 

I am definitely going to put a aftermarket head on the wheeer, I am probably going to just keep the air box as is. And thanks for your help! If I didn’t see your reply I probably would have went out and bought a $300 450 carb and been disappointed 😂

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By ResQ91
      Hi Guys!

      New member and could really use your advice. I would have to believe this has been an issue for others but a search here came up with nothing......? (Probably me not doing search correctly)
       
      I have an 87 Big Bear 350 YFM350FWT
      The OEM Mikuni BTM carb is shot and would rather replace than rebuild.
      It is no longer made and I have had good luck with NICHE carbs so I ordered a #K-CRB-0006 This was what they said was replacement when ordered. This Carb only uses 1 Throttle cable. The Slide is linked so it uses one. (OEM had 2nd cable coming through top to move slide)
       
      Problem is when I ordered a replacement Cable from NICHE (#C-CBL-0061) the Cable wire is a little short, not allowing Throttle to return all the way down to Idle position. I called NICHE and they are at a loss. Haven't gotten back to me after 2+ weeks.
       
      What would you recommend other than a carb rebuild?
      Can I just use 1 of the OEM cables (It is the right length) and snip/disconnect the other that went to top of Carb for Slide?
      Or ??
       
      Thanks in advance for any advice you have!!
       
      Dave
    • By kiriyaaoi
      Hello everyone, I just picked up an 02 LT-F250F the other day and have been in the process of tearing it down to fix some stuff- one of which was the cylinder base gasket leaking like a sieve. Well, I know why that is now, and I also discovered that someone had been in there before. I didn't take pictures, but it looks like it was probably run low on oil at some point, the cam journals and the "bearings" (for lack of a better term) in the head and the valve cover are totally wiped out, very deep grooves.  From what I know it's very difficult to repair aluminum in this way, so I'm trying to figure out where to go next.
       
      1. Have someone grind down the head and valve cover and fit actual bearings in since the aluminum is screwed, and have the cam ground down to match.  I have no idea what this would cost.
      2. Buy a replacement head+cam+valve cover.
       
      #1 I was hoping someone might have some advice on, but #2 seems like it'll (probably) be the more cost effective option.  However I'm running into some difficulty, it seems like the 2001 and 2002 models specifically use a different head part number,  11100-19B10, instead of  11100-19B01 like for all earlier models.  What exactly is the difference between them? There are obviously far more of the earlier heads because it ran for over 10 years.  Are they actually interchangeable? I've also noticed there are heads from the LT250EF that has 4 valve heads but also otherwise look identical.  Would those work as well possibly?  I'd like to not have to drop $500 on machine work or new heads on a $1300 quad that I'm already putting a bunch of new parts on.  Oh, and it has a new piston and the cylinder itself looks pretty good too, as I said someone was in here before me.
       
      Any help or advice would be greatly appreciated. I'll post pics of the carnage tomorrow.
         
       
    • By Admin
      View File 2006-2011 Honda Rincon TRX 680 FA/FGA service manual
      2006-2011 Honda Rincon TRX 680 FA/FGA service manual
      Submitter Admin Submitted 04/09/2024 Category Honda ATV  
    • By kantrud97
      Hello i have a 2005 Bombardier Outlander max xt 400, i recently split the case to fix a oil leak. while in there i took out the oil pump and i cant find the torque specs for the oil pump to go back in, i tend to over tighten everything so im trying to go be the torque specs so i dont break anything.
       
      Thank you in advance
    • By Suzukiquad
      If you had to choose one mod that you couldn't live without, or had to recommend one what would it be? 
×
×
  • Create New...