Quantcast
Jump to content

Recommended Posts

Posted

Hello folks, I have a yamaha timberwolf 250 motor I'm putting into a tri moto 200 frame and need some help with the wiring for it. The wiring harness I got with the motor has been damaged and missing a small section so my issue is that I have 3 white wires coming from the stator assembly which connect into another 3 white wires on the voltage regulator. My question is does it matter which of those white wires go connected together or are each of the white wires different and need to be connected to the appropriate wire on the voltage regulator. Any advice or help is appreciated. Thanks.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Popular Now

  • Similar Forum Topics

    • By Joeguy
      After i did my rebuild it seems to not want to shift well. I think the cable is alright, and when it does shift its nice and solid. I have to basically use my hand to shift and i have to pull or push it very far, like max travel, to get it to shift. I also tried adjusting the clutch set screw. Any ideas where to go next, or maybe i should just grab a new cable to try.
    • By cfherrman
      Fixing for a friend. Atv was at a different friends house to be fixed and he rebuilt the carb and had it running nice, then it shut off and no more. He replaced the key and the coil.
       
      So he got busy, so I am helping, I checked the wiring from the stator to the cdi, and from the cdi to the coil. All is good. I checked resistance on the pickup coil, good, and on the source coil, open. I buy a new stator (China) and the 4 prong plug only has 3 wires in it while mine has all 4. I checked resistance in the source coil and it's in the 300's. I pulled one of the old pickup wires out of the old stator and wire it in the new one. Still no spark.
       
      Why do the wires differ, I checked the VIN again and it's "J" for the year and I got a 1988 stator. Please help!
    • By Dsluder
      I am having an issue with a hs500. I bought it broken and have been trying to get it running. It seems to be starving for fuel. If I put my hand over the intake it will crank but will not run for very long because I'm not able to get the correct airflow with my hand. The things I have done so far are. Replaced the fuel pump, fuel filter, mass airflow sensor, idle air adjuster, fuel injector, cleaned the throttle body, replaced the ecu, and still the same issue. I notice the injector does not spray when removed from the head. I dont know if that is common. 
       
      I am out of ideas on what to do next. I have removed the fuel line from the injector and it is getting plenty of fuel. If anyone has an idea on what could possibly be the issue I would be happy to try anything at this point.
    • By flyinbrian365
      View File 2023 Yamaha RMAX4 Wolverine 1000 service manual
      Factory service manual
      2023 Yamaha RMAX4 Wolverine service manual
      Submitter flyinbrian365 Submitted 06/08/2026 Category Yamaha UTV  
    • By flyinbrian365
      View File 2021-22 Yamaha RMAX4 1000 Wolverine service manual
      Factory service manual
      2021-22 Yamaha RMAX4 1000 Wolverine service manual
      Submitter flyinbrian365 Submitted 06/08/2026 Category Yamaha UTV  
×
×
  • Create New...