Quantcast
Jump to content

Recommended Posts

Posted

Can you put a 8 coil stator in a 2004 Suzuki LT80 if I switch over to CDI box the rectifier and everything else with it that's if it bolts up to the old one rectifier place

 

16834846950658492250553219774582.jpg

  • Ajmboy changed the title to 2004 Suzuki LT80 stator
Posted

I see no reason that it wouldn't work, as long as you replace the electronics that go with it, but it has to be an exact fit, if the pickup coil is not in the correct position with the rotor it will not generate the voltage needed for spark.

  • 2 weeks later...
Posted

So I got a new stator put it in everything has spark and what  it needs to start but it won't start. The standard that came out of it or the videos that I watched had a notch on them do you lined up this one doesn't have that on it so I don't know what position to put it in anybody know what I can do

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By ATVNetwork
      As the 2025 ATV Motocross National Championship Series (ATVMX), an AMA National Championship, got underway with back-to-back Florida AMA Pro only events, it was evident that Phoenix Racing Yamaha’s Joel Hetrick picked up where he left off last season.View the full article
    • By Mhatayas
      What should I do about this , bad oil leak where the filter cover bolts on . Can I use some gasket maker 

    • By TravisM
      2001 bayou 220 KLF220A
      Need some help putting a new ignition switch on this thing. I'm not finding homes for all the wires. I can hook up the white wire and brown wire, But the switch has a B/W and Solid Yellow wire i can't find a home for, and there aren't any more wires in the vicinity from the harness that match this, except one red wire with a double female end crimped on, and a few B/Y grounds. None of the wiring diagrams i've founder or have been given match.
      I'm also wondering if i have the wrong switch? some switches appear to have 4 wires and other just 2, the Brown wire and a White wire.
      I'm at a loss here. Thanks.
       
    • By mans
      Were is the neutral safety switch on 03' Kodiak 400 4x4 . How xan i check it to see if it's good for a no neutral light no power to machine. Ty
    • By Snick
      Bought the project a few weeks ago with weak and intermittent spark. I could smack the CDI box with a screwdriver and it would work fine for a few days. Now, the smack trick is not working and machine is running awful with the weak spark and will most often not fire enough to turn the engine over through combustion (cranks very good). I ordered the GY6 CDI to see if I can get it going again as these CDI boxes are way too expensive even used. battery is fully charged and charging very good.
       
      Wondering if anyone knows how the GY6 (6-pin AC) CDI would wire to this machine. Attached is the electrical diagram. My confusion is with the green and orange wires sharing the 2-pin connector and the Blk/Red wire that runs to the magneto solo. How would I get AC power to the CDI through pin 1 on the GY6 when the CDI has two wires to the pickup-myabe just try one (orange then green) at a time?
       
       
       


       
      ^PINOUT:
            5   6
            2   4
           1    3
×
×
  • Create New...