Quantcast
Jump to content

Recommended Posts

Posted (edited)

Hey all, I'm a 2-stroke quad/dirt bike guy, new to utility atvs. Just picked up a pretty clean looking 2005 Kodiak 450 4x4 with about 1,000 hours on it for my dad.

The first thing I noticed when we got home was oil leaking from a seal on the rear axle. Pictured below. I've been staring at this frigan Partzilla diagram for days and can't figure out what part this is. What is it and what likely needs replacing/fixing?

Also wouldn't mind any recommendations on the next things to check. The owner said nothing's been replaced on it but oil since it's been in service. Def needs new rear tires.

Thanks all!

IMG_9785.JPG

IMG_9990.JPG

Edited by rockfresh15
  • rockfresh15 changed the title to 2005 Kodiak 450 4x4 rear axle oil leaking
Posted

Yeah the seal is leaking, is is a very tiny leak, and as Mech said part #12, that is the fix, but me being the person i am i have to know why it failed, i would remove the dust cover and see if you can pin point the leak, see if anything has pinched the seal such as corrosion, trash stick, dust cover etc, sometimes you can get a small leak like that to stop if you clean it up a bit with kerosene, thats cause the seal to swell a bit, but most times seals just fail and have to be replaced. Just something to look at before you tear the axel out. 

  • Thanks 1
Posted

I think that seal can be changed without pulling the axle out..  I'd have a small lever/hook that would pull it out I'm pretty sure. If you can get something between the seal and the axle, something with a slight turn or hook at the end, you can quite likely pull/lever it out.

And yeah, I'd check why/if there's a reason it's leaking.. Perhaps a bit of grass wrapped around the axle, or a worn bearing, or the breather's blocked and the housing is pressurising when it gets warm.

  • Thanks 1
Posted

I'VE GOT THE SAME PROBLEM ON A1992 YAMAHA BIG BEAR 350.  WHEN I ORDERED THE SEALS, I GOT THREE.  MY REPAIR MANUAL INSTRUCTS ME TO REMOVE THE REAR END, REMOVE THE AXLE BY SLIDING IT OUTOF THE HOUSING, THEN REMOVING THE SEALS FROM THE INSIDE OF THE HOUSING.  THIS MADE A SIMPLE JOB, NOT SO SIMPLE.

Posted

Ahh, ok thank you guys! This is my dad's quad so I'll have to take a crack at all this in a month or so when I'm back in town. How serious could it be in terms of what's causing it?

Anything else I might wanna look into checking on the bike?

  • 3 months later...
Posted
On 9/18/2023 at 9:56 PM, rockfresh15 said:

Ahh, ok thank you guys! This is my dad's quad so I'll have to take a crack at all this in a month or so when I'm back in town. How serious could it be in terms of what's causing it?

Anything else I might wanna look into checking on the bike?

just keep a eye on the fluid level until you fix it. Mines been leaking for years lol

 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Popular Now

  • Similar Forum Topics

    • By Fonne
      Hi 
      Is looking for a quad to pull a flail mower as my first priority, but also a bit of fun. 
      So its going to be pulling a flail mower on high grass / weed on a bumpy field at pretty low speed. 
      My budget is not high, so is mostly looking at a old Yamaha Kodiak 400cc / Suzuki Eiger 400cc or similar. 
      What machine would you recommend  ?  - Really want a solid machine since I am no mechanic but can perform a early service myself. 

      (English is not my native, hope it makes sense)

    • By mehim
      Hi everyone and thanks for reading. 
      My husband and me are getting ready to host the 2nd Quad Runners event at our nudist campground. The first one (last year) went pretty well with about 20 quads attending and have to say, it was a smaller group, but they made up for their size with the large interest in partying and there was plenty of nudity as the Saturday night went on. 
      We have decided to host another one this summer, but we are looking for some fun (but safe) riding events. Our grounds are almost all flat and remember we are a nudist campground so many of us are bare as* naked so "slow ride" events would be the best. 
      Give us your thoughts and ideas and feel free to ask us anything you would like, and we will answer right here in the thread. 
      Thanks for your help and ride safe. 
      BTW, let us know what "anything goes" means for this thread section. 

    • By logray
      Hi all, 

      I am wondering if any of you have a Clutch Starter gear from a 1988 era quadrunner 250 sitting around that you could get me a precise measurement of the outer diameter of the race the sprag engages onto, for me? I need to machine a damaged race down and install a hardened sleeve and need that measurement (it's on a different gear than the OEM one, so I can't buy and use a OEM gear). 

    • By Mikey509
      Hi guys, I was given a 2000 Honda Recon fourtrax 250 (I think that's the full name lol). The previous owner had it sitting for a while before I got it. It sat for another few years in my ownership. I got it up and going on its first test drive today!! I was wondering where everyone buys their parts from?  Coming from the car community, we have sites like RockAuto and many more. Anything like that for quads? Also would like to be pointed in a direction, if possible, for plastics. I am missing a few and would like to have it complete. I appreciate any input!
    • By Shorty51
      Good morning, I am new to the forum. I'm 75 years old and love getting ATVs back to usable condition. I particularly like the 2006-2009 Arctic Cat 250 Utility. I currently own 6. The 2006 I am working on only has reverse and low gear. The "drive shaft" in the transmission is completely stripped where the high gear would mesh. Has anyone on here replaced the shaft. I'm told I have to split the case. I was hoping that someone on here could let me know how hard it will be. I already have it stripped down to where the shaft coming in from the clutch side is the only thing left. I was hoping I could just remove the driven clutch and drive it out from there. Directions say different. Any help would be greatly appreciated.
×
×
  • Create New...