Quantcast
Jump to content

Recommended Posts

Posted

As it should be easy to see I am not a four wheeler mechanic so I apologize for asking for help, I replaced my OEM carburetor with a aftermarket carburetor and with y’all’s help adjusted the air/ fuel and it ran great until this evening and I noticed a smell of fuel I inspected carburetor area and found a steady flow at the vent line on the bottom of the carburetor so my question is is the float the only thing that will cause this problem? Before I installed the carburetor I checked the jets for tightness and they all seemed fine?

Posted

The float could be stuck partly open or  misadjusted. about the only thing I can think of otherwise is if there is a drain valve on the floatbowl bottom it could be stuck open  by a bit of debris if you   pushed the button  to  let a little  fuel/  water out.

  • Like 1
Posted

It sounds like the float needle has got some dirt or fluff under it. The float needle's seat has an O ring to seal it to the carb body and those can leak too but it shouldn't be the case with a new carb that was ok to start with. Check the drain screw is done up first though if it has one, or check the drain valve if it has one as Dave is suggesting. I'm in New Zealand and I've never seen a drain button. I'd also turn the tap off and run the bowl empty, then turn the tap on and start tapping the carb body fairly hard around where the float needle is with a screwdriver handle.. It may just flush the dirt or wriggle the needle into a better position and it might come right. It works sometimes !

Sounds though like you might need to clean the fuel tank or tap filters or fit an after-market fuel filter.

  • Like 1
  • 2 weeks later...
  • 7 months later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By kawasig
      Hello there
      I'm having a problem finding a quality carburetor for a 1993 Suzuki Quad Runner lt-f 250 2x4. I find a lot that have 3-4 star ratings. And all so far don't have the right throttle Cable inlet at the top. The last one I got 4 star on Amazon has a threaded cable sheath rest that could be partially drilled to work. I would prefer to get one I don't have to modify. Any recommendations are greatly appreciated!
    • By Callaway
      I am trying to diagnose a no spark issue with my 02 Big Bear 400 and I am really hoping it is not a CDI.  I have done the test on the stator and I believe that is faulty.  I ordered a new aftermarket one from a the jungle website and it tested bad right out of the box so I am waiting for a different one to arrive from an ATV parts supplier.  I started looking out of curiosity at CDI units and it seems if it is for a big bear you are SOL.  Kodiaks, no problem.  Big Bear. No such luck.  
    • By Gkb
      Need ideas for all aftermarket accessories for my new atv
    • By 97kingquad
      Okay so I bought this 1997 sazuki king quad from a guy and he had it for a few years. 
      He had it registered and on the trails last year but he said it bogged and backfired when he would try to drive it. so it sat for a year. 
      I bought it for 800 bucks and got it running that night and it ran great for a few days 
      But I parked it the other night and went to start it again and it was really hard to fire up and when I did it was bogging and idling high then low again.
      So I took the carb out and cleaned it (ended up doing it twice because it was still doing the same thing) 
      Now today I have it running slightly better, but it is still like 20% 
      I have been looking it up and trying to figure it out but I can't find the issue, has anyone else had this problem? I'll attach a video of it running and giving some throttle 
    • By TravisCr
      I don't know if I shouldn't have posted but I this is my second post on this (other was in regionals Forum)  The family has a 2-up 2004 Artic Cat and a 2003 Polaris Sportman and we are looking for fun/easy rides in the Colville, WA area- 70 Miles North of Spokane WA, we have a small trailer we can haul these with but need to find some good areas for beginner.

      Thanks in advance for any suggestions.
×
×
  • Create New...